Why does my GMC S15 die at high idle?
Recently my truck has began to die when coming back down to idle. In looking at the fuel injection, I can see the injectors stop injecting fuel. After it dies, it is very hard to restart unless it is left alone and cools a bit. If the IAC is unplugged, the engine will run at high idle fine.
Why does my Sonoma S15 stall and die?
I have a 98 sonoma ( 4 cyl.) that runs great and strong going down the road but when I stop and start to take off it bogs down and dies, It will start back up in 5 to 10 mins. and will run good for several days and then it will die again . I have been told that it is the 3rd cycl.
What to do if your GMC Sonoma dies?
The module plug at the key assy, remove plug and clean contacts, that should do it. In the mean while try this, turn key to run, shift into neutral, then start, might work. I have a gmc sonoma that i will be driving and then all of a sudden will jerk and sputter and at times will die.
What kind of engine does a 1995 Sonoma have?
I’ve got a 1995 Sonoma with the 2.2 and it suddenly quit while I was driving on the interstate at about 70 mph. I got it home via AAA and found I had plenty of fuel pump pressure as well as spark.
Recently my truck has began to die when coming back down to idle. In looking at the fuel injection, I can see the injectors stop injecting fuel. After it dies, it is very hard to restart unless it is left alone and cools a bit. If the IAC is unplugged, the engine will run at high idle fine.
I’ve got a 1995 Sonoma with the 2.2 and it suddenly quit while I was driving on the interstate at about 70 mph. I got it home via AAA and found I had plenty of fuel pump pressure as well as spark.
Can a bad throttle position sensor cause idle surging?
Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. 3) Check Engine Light
What should I do if my GMC S15 dies?
After it dies, it is very hard to restart unless it is left alone and cools a bit. If the IAC is unplugged, the engine will run at high idle fine. When plugged back in, the correct idle resumes and it may run a few seconds or a minute before it dies. I am getting fuel to the injectors.
What causes the idle speed to go up or down?
The idle air control valve is programmed to regulate and maintain the engine idle speed at a constant rate. If the valve fails or has any issues it can cause the idle speed to be thrown off. This may result in an unusually high or low idle speed, or in some cases a surging idle speed that repeatedly climbs and falls. 2. Check Engine Light comes on
What are the symptoms of a bad idle control valve?
$0.00 1 Irregular idle speed One of the most common symptoms commonly associated with a problematic idle air control valve is irregular idle speed. 2 Check Engine Light comes on Another symptom of a potential issue with the idle control valve is an illuminated Check Engine Light. 3 Engine stalling
What should the idle speed be on a GM TBI?
Insert a T-30 size Torx driver into the Idle adjustment screw that is located behind the plug removed earlier. Turn the screw to adjust the idle speed to 650 RPM +/- 50 RPM. Turn off the engine and disconnect the negative battery terminal from the battery using a wrench.
The idle air control valve is programmed to regulate and maintain the engine idle speed at a constant rate. If the valve fails or has any issues it can cause the idle speed to be thrown off. This may result in an unusually high or low idle speed, or in some cases a surging idle speed that repeatedly climbs and falls. 2. Check Engine Light comes on
$0.00 1 Irregular idle speed One of the most common symptoms commonly associated with a problematic idle air control valve is irregular idle speed. 2 Check Engine Light comes on Another symptom of a potential issue with the idle control valve is an illuminated Check Engine Light. 3 Engine stalling
Insert a T-30 size Torx driver into the Idle adjustment screw that is located behind the plug removed earlier. Turn the screw to adjust the idle speed to 650 RPM +/- 50 RPM. Turn off the engine and disconnect the negative battery terminal from the battery using a wrench.
How much does an idle control valve cost?
$92.73 – $160.32. Price range for all vehicles. Average rating from 17,525 customers who received a Change Oil and Filter. The idle control valve, also commonly referred to as the idle air control valve, is an engine management component that is found in one form or another on the majority of road going vehicles.
When does the idle air control valve change?
When the engine is running but the vehicle is not moving, this means the engine is idling. During this time, the number of revolutions per minute (RPM) inside the engine will change. The idle air control valve is responsible for managing the engine idle speed.
What happens to your car when you idle?
A rough idle will result in intense vibrations forming whenever your vehicle is stopped with the engine running. Since less air will be going into the engine during its idle state, the car will react by shaking profusely.
What causes idle surges on a car ECM?
Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges.
After it dies, it is very hard to restart unless it is left alone and cools a bit. If the IAC is unplugged, the engine will run at high idle fine. When plugged back in, the correct idle resumes and it may run a few seconds or a minute before it dies. I am getting fuel to the injectors.
How often does my Town and Country shut down?
There is no pattern to when it shuts down. I may drive 20 miles with no problem and other times it will shut down 5 or 6 times within that distance. Had it to the Chrysler garage for repairs and $1400 later the problem was still there.