What is the drive cycle for a 99 Honda?
Then let off the gas and let the car slow down and then stop. After than, you need to accelerate to 65, slow down to 50, and back to 65, then 50 a few times without hitting the brake.
What should the fuel level be on a Honda Accord?
Driving your Honda Accord in the manner below should make the required Emission Monitors “Ready”. Before you start the Drive Cycle make sure your Honda Accord’s fuel level is between 1/4 and 3/4, otherwise the EVAP test won’t run. Make sure to obey all traffic laws while performing the drive cycle. 1.
How to check the drive cycle on a Honda?
The Honda Drive Cycle is included in recent owners manuals. You can either use an OBDII scanner or, if one is not available, check the MIL (check engine light) because Honda/Acura will indicate, on vehicle startup of the readiness monitors are set. When you turn the ignition to On-2 without starting the engine, the MIL will come on for 20 seconds.
How to make a Honda Accord monitor ready?
Honda Accord Drive Cycle (required to make monitors ready) A. Begin by idling the engine while 2 1/2 minutes. Next idle for another 2 1/2 minutes with the A/C compressor and rear defroster on and while the transmission is in Drive (D); only of automatic transmission.
How many miles does a 1999 Honda Accord EX have?
Mileage: 168,918 miles Body Type: Sedan Color: Black Engine: 4 Cyl 2.3 L Accident reported. 1st owner purchased on 12/01/98 and owned in OH until 07/02/14 • 2nd owner purchased on 08/16/14 and owned in OH until 01/14/20. 1st owner drove an estimated 3,846 miles/year • 2nd owner drove an estimated 7,756 miles/year.
When did the Honda Accord EX come out for sale?
No accident or damage reported to CARFAX. 1st owner purchased on 11/08/99 and owned in OH until 06/08/17 • 2nd owner purchased on 06/08/17 and owned in OH until 08/14/18 • 3rd owner purchased on 08/14/18 and owned in OH until .
Then let off the gas and let the car slow down and then stop. After than, you need to accelerate to 65, slow down to 50, and back to 65, then 50 a few times without hitting the brake.
Driving your Honda Accord in the manner below should make the required Emission Monitors “Ready”. Before you start the Drive Cycle make sure your Honda Accord’s fuel level is between 1/4 and 3/4, otherwise the EVAP test won’t run. Make sure to obey all traffic laws while performing the drive cycle. 1.
Can a drive cycle work on a Honda Civic?
Keep in mind, my car is a 1999 Honda Civic so this drive cycle should definitely work if you drive a 1996-2000 Honda Civic. Hypothetically, this drive cycle should also work for Acuras between the same years. Older or newer Honda’s and Acura’s, I can’t guarantee this foolproof method will work but it’s worth a shot.
How to reset the OBD II drive cycle?
Decelerate without using the brake (coast down) to 20 MPH or less, then stop the vehicle. Allow the engine to idle for 10 seconds, turn the key off, and wait one minute. Restart and accelerate to 40-55 MPH at 25% throttle and maintain speed for two minutes.
The Honda Drive Cycle is included in recent owners manuals. You can either use an OBDII scanner or, if one is not available, check the MIL (check engine light) because Honda/Acura will indicate, on vehicle startup of the readiness monitors are set. When you turn the ignition to On-2 without starting the engine, the MIL will come on for 20 seconds.
Keep in mind, my car is a 1999 Honda Civic so this drive cycle should definitely work if you drive a 1996-2000 Honda Civic. Hypothetically, this drive cycle should also work for Acuras between the same years. Older or newer Honda’s and Acura’s, I can’t guarantee this foolproof method will work but it’s worth a shot.
What’s the drive cycle for a Honda Acura?
Idle for 20 seconds again. Go to a highway and drive between 50-60mph for 20 minutes. You should be in D or 5th gear. Don’t utilize cruise control. At some point in the journey, coast for 90 seconds (take your foot off the accelerator). Conduct city driving for 10 minutes, and during this time, perform some coasting.