Where is the fuel pump on a Pontiac Grand Am?

Check in the engine compartment fuse box, it should be near the battery under the hood. The cover should be pretty easy to remove. The fuel pump should be connected through a fuse in slot 48. If that fuse looks good, then you may want to check the fuel pump relay (also inside the engine compartment fuse box).

Why is the starter not turning on my Pontiac Grand Am?

If you can hear the starter motor turning but the engine isn’t turning (look at the belt) then the starter may not be engaging (in your car I believe this means that you must replace the whole starter). You can remove and test your starter to confirm whether or not the solenoid is engaging the starter.

What kind of car is the Pontiac Grand Am?

The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. 2003 Grand Am will not start.

Why is there no fuel getting to the engine?

If the fuel injector fuse (s) are blown due to a wiring issue, this may cause your problem. A clicking noise can be heard from each injector when they are working properly. I would recommend having a technician from YourMechanic try to start your vehicle with starter fluid.

How can you tell if your fuel pump is failing?

If you ignore all of the other warning signs of a failing fuel pump, it will eventually fail completely. Once your fuel pump has finally given up the ghost, no fuel will reach your engine. You may hear your spark plugs firing when you try to start your car, but without fuel, the engine won’t be able to turn over.

When is it time to replace your fuel pump?

Like any device, however, fuel pumps can and do eventually wear out after thousands of miles of use. If your car struggles with weak or inconsistent power, it may be time to replace the fuel pump on your car. Have you ever had to deal with a failing fuel pump?

What does the fuel pump shut off switch do?

This device is analog to an electric circuit breaker, but only for fuel, not electricity. Many vehicles come with a fuel pump shut off switches. The inertia switch is a security measure implemented by car manufacturers to shut off the fuel supply in case of a car crash or accident where a vehicle comes to a sudden stop instantly.

When do you reset the fuel cut off switch?

After speeding over a deep pothole, speed bumper, or after a car accident, you could end up with an engine unable to start. In most cases, you only need to reset the fuel cut off switch, which was activated by the impact. It looks simple, right?

Where is the fuel cut off switch on a Ford Fiesta?

Steps to Locate and Reset Fuel Cut Off Switch on Ford Fiesta (For Other Cars Keep Reading) First, open the glove compartment. Pull out the glove compartment by firmly pressing the left side toward an inner section. Look for a device with a rubber yellow cap on it. Push the rubber yellow cap on inertia switch.

Why is my fuel pump reset button not working?

Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc. As a first step best to see if there are any stored trouble codes that could point directly to the fault.

How do you reset the fuel pump shut off switch?

The inertia switch is a security measure implemented by car manufacturers to shut off the fuel supply in case of a car crash or accident where a vehicle comes to a sudden stop instantly. How to Reset Fuel Pump Shut Off Switch Similar to an electrical circuit breaker in your home, you can reset it by pushing the button or pulling the leverage down.

Where is the fuel cut off switch on my car?

Under side panel located next to the drivers door; On the driver side, between footrest area and door, sometimes hidden under the carpet. After finding the switch, it is very easy to reset it with one push of a button. Now put the key in and start the engine.

The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. 2003 Grand Am will not start.

Can you change the PCV valve on a Pontiac Grand Am?

You can buy an original equipment replacement from Car Stuff for all Pontiac Grand Am engine types made between 1994 and 2005. Pop the new PCV valve into the spot of the old valve. With the correct part, it should snap right in. Take the hose and reattach it in order to complete the installation.

What kind of valve does a Pontiac have?

Over the years, GM made a number of Pontiac car vehicles, including the Firebird, Bonneville, Sunfire and GTO. Modern Pontiac car cars have PCV valves. The PCV (positive crankcase ventiliation) valve helps to regulate the engine’s fuel fumes.

How do you change the PCV valve on a Pontiac Bonneville?

Push the new PCV valve into the intake of the Pontiac Bonneville. The larger end goes into the grommet while the shorter end is reattached to the hose. Replace the cover and you have finished installation. Loosen the nut around the negative (-) battery cable, then pull the cable away from the terminal.

Why does fuel gauge read wrong after fuel pump replaced?

Fuel gauge reads wrong after fuel pump replaced – YouTube If you have a 96 or 97 year gm truck that needs a fuel pump, be sure to order it by the VIN. There is an option for a anti-slosh module that could cause you If you have a 96 or 97 year gm truck that needs a fuel pump, be sure to order it by the VIN.

Can a fuel pump be replaced in a Pontiac Grand Prix?

The Pontiac Grand Prix has an electric fuel pump so you should ensure that its fuses and relays are working before checking it. You may need to clean your fuel pump or replace it if your gas tank is not empty, but your vehicle has difficulty getting fuel.

What should I do if my fuel pump is not working?

A clicking noise can be heard from each injector when they are working properly. I would recommend having a technician from YourMechanic try to start your vehicle with starter fluid. This should give the engine enough fuel to run long enough to see if the injectors are working correctly.

When did the last Pontiac Grand Prix come out?

Models made from 1997 to 2003 will have a 3.1 L or 3.8 L engine. The last generation was produced from 2004 to 2008 and had a 3.8 L, 3.8 L supercharged or a 5.3 L engine. Prepare your vehicle for fuel pump servicing.

Where is the fuel pump relay on a Pontiac Grand Am?

The fuel pump relay is #18 in the fuse box. Start with the car off, and have somebody else put the key in the cars ignition and attempt to start the car while you listen to the relay. If you can hear this relay make a “clicking” noise as the car attempts to start, then it is working properly.

Why does my GM 3.8L have no spark?

Here are the most common causes of a no-spark result: CASE 1: Spark was present in all of the cylinders This result tells you three very important things: 1.) the crank sensor is good, 2.) the ignition control module is OK, and 3.) the ignition coil coil packs are good. You don’t have to spend any time testing them or any money replacing them.

What causes the fuel pump to not start?

The fuel pump is running and delivering normal pressure to the engine But, with all that working your engine still will not start. So, the most likely cause, is that the fuel injectors are probably not opening. The (PCM) uses the trigger signal from the crankshaft position sensor; and/or camshaft position sensor to pulse the injectors.

Where is the pressure regulator on a Pontiac Grand?

Disconnect the fuel return line from the pressure regulator, located at the end of the fuel rail using a wrench. Pull the vacuum hose from the port on the pressure regulator. Unscrew the fasteners attaching the fuel pressure regulator to the fuel rail using a Torx screwdriver. Pull the regulator from the fuel rail.

How to check fuel pressure on a Pontiac Grand?

Attach the vacuum hose to the port on the fuel pressure regulator. Plug in the electrical connection for the fuel pump near the fuel tank on 2.4-liter models. On 2.2-liter and V-6 models, replace the cap on the end of the fuel rail.

Why does my GM 3.8L engine not start?

If no voltage is present, as your helper cranks the engine, then the cause of no fuel condition is due to either a bad fuse, fuel pump relay. The engine in your vehicle could be bad and the source of the ‘cranks but does not start condition’. The way to find out if the engine is the cause of the no start is to do a compression test.

Where is the fuel tank cap on a Pontiac Grand?

Plug in the electrical connection for the fuel pump near the fuel tank on 2.4-liter models. On 2.2-liter and V-6 models, replace the cap on the end of the fuel rail. Eric Grosso has been a journalist since 2002, working as a staff reporter covering government events, school districts, sporting events and entertainment acts.

Where is the fuse box on a Pontiac Grand Prix?

Here you will find fuse box diagrams of Pontiac Grand Prix 2004, 2005, 2006, 2007 and 2008, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay. It is located on the right side of the dashboard, behind the cover.

Where is the fuel pump relay located on a car?

The fuel pump relay is an electronic component that is found on virtually all vehicles equipped with an internal combustion engine. It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by…

Where is the fuel pump control module located?

It is often found in the fuse box located in the engine bay and functions as the primary electronic switch that controls power to the fuel pump. The fuel pump relay is usually controlled by the ignition or Powertrain Control Module, and when switched on, will provide current to the fuel pump so that it may function.

What is the average rating of a fuel pump relay?

Average rating from 198 customers who received a Car is stalling Inspection. The fuel pump relay is an electronic component that is found on virtually all vehicles equipped with an internal combustion engine.

What kind of fuel pump does a Pontiac Grand Prix use?

Determine which fuel pump your Pontiac Grand Prix will need. This depends not only on the make and model, but also the engine size. Models made from 1962 to 1968 will have a 389 cubic inch (ci), 400 ci, 421 ci or 428 ci engine. Models built from 1969 to 1972 may be equipped with a 400 ci, 428 ci or 455 ci engine.

What are the symptoms of a fuel pump relay problem?

1. Engine stalls One of the first symptoms of an issue with the fuel pump relay is an engine that suddenly stalls. If the fuel pump relay has an issue while the vehicle is operating it will cut off power to the fuel pump, which will cause the engine to stall.

How much does a GM fuel pump cost?

As mentioned earlier (in fuel pump test 2), in all of the GM 3.1L and 3.4L V6 equipped vehicles GM was kind enough to put a Schrader valve on the fuel injector rail where you can tap into the fuel system and check its performance. A fuel pressure gauge can cost you as little as $40 (US) or as much as $200 (US).

Why is my GM 3.1L fuel pump not working?

CASE 2: If the fuel pressure gauge registered 35 PSI. This fuel pressure gauge result lets you know that the fuel pump is working and delivering enough fuel to the fuel injectors. The reason your 3.1L or 3.4L GM vehicle is not starting is due to another reason.

Do you have to fill the gas tank when installing a new fuel pump?

Having the gas tank at least half-filled is important when you are installing a new fuel pump. Checking these issues is a great way to ensure that the problem is being properly addressed.

What kind of engine does a Pontiac Grand Prix have?

Models made from 1962 to 1968 will have a 389 cubic inch (ci), 400 ci, 421 ci or 428 ci engine. Models built from 1969 to 1972 may be equipped with a 400 ci, 428 ci or 455 ci engine. Look at later generations of the Pontiac Grand Prix.

Where is the fuse box on a Pontiac Grand Am?

Cigar lighter (power outlet) fuse in the Pontiac Grand Am is the fuse #34 in the Engine compartment fuse box. There are two fuse blocks, which are located on the right and left in the dashboard, behind the covers. How to check the fuses? How to replace a blown fuse? Why do car fuses blow?

When did the Pontiac Grand Am 5th generation come out?

In this article, we consider the fifth-generation Pontiac Grand Am, produced from 1999 to 2005. Here you will find fuse box diagrams of Pontiac Grand Am 1999, 2000, 2001, 2002, 2003, 2004 and 2005, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout) and relay.

How to test the fuel pump in a GM 3.8L?

In all of the GM 3.8L V6 equipped vehicles, GM was kind enough to put a Schrader valve on the fuel injector rail where you can tap into the fuel system and check its performance with a fuel pressure test gauge. A fuel pressure gauge can cost you as little as $40 (US) or as much as $200 (US).

Can a fuel pump go bad on a mini van?

When the fuel pump goes bad on your GM 3.8L equipped car or mini-van, it’s going to crank but not start. Although it stinks that your vehicle is not starting, the cool thing is that testing the fuel pump is not hard.

What are the symptoms of a bad fuel pump?

Symptoms Of A Bad Fuel Pump. Which And Where To Buy A Fuel Pressure Gauge. FUEL PUMP TEST 1: Fuel Pressure Test With Gauge. FUEL PUMP TEST 2: Using Starting Fluid. More 3.8L V6 GM Tutorials. You can find this tutorial in Spanish here: Cómo Probar La Bomba de Combustible (GM 3.8L) (at: autotecnico-online.com ).

What does 0 psi mean on fuel pump?

The fuel pressure gauge will register 0 PSI. OK, let’s analyze your test results: CASE 1: If the fuel pressure gauge registered 0 PSI. This confirms that the cause of your 3.8L equipped GM car or mini-van is caused by a lack of fuel.

Pontiac Grand Prix (2004-2008)…>>. Cigar lighter / power outlet fuse in the Pontiac Grand Prix is located in the Instrument panel fuse box (see fuse “CIG LTR”). It is located in the glovebox, behind the cover on the right.

How do you test a bad fuel pump?

Removing the fuel line that connects to the fuel injector rail (this is the one that delivers fuel from the fuel filter) and place it in a container. When ready, have your helper bump the starter motor while you verify if fuel comes out or not. No fuel coming out of the fuel line further confirms a bad fuel pump.

How to test the fuel pump in a mini van?

This is due to the fact that GM has included a Schrader valve on the fuel rail to which you and I can attach a fuel pressure gauge to. Using a fuel pressure gauge to make sure that enough fuel is reaching the fuel injectors is the most accurate way to diagnose the fuel pump in your car or mini-van.

What to do if your fuel pump is not working?

Check out your vehicle’s service manual to find out where to check and the proper procedure for checking it. Test for source voltage, to determine whether or not the good charge that’s leaving the fuse is getting to the pump. If no power is making it to the fuel pump, then check the fuel pump relay circuit.

How can I check the pressure on my fuel pump?

Attach the fuel pressure gauge at the fuel rail test port. Cycle the key on and off a few times and watch the pressure should go up to specifications and not drop for a long time or more than ten minutes before any drop of more than 1 or 2 psi is seen.

What kind of engine does the Pontiac Grand Am have?

The Grand Am shared the same front-wheel drive platform as the Buick Somerset (renamed Skylark in 1987) and the Oldsmobile Calais. Initially, the Grand Am was available in base or LE trim in coupes only. The 2.5 L Tech IV was standard, while a 3.0 L Buick V6 was optional.

How to check fuel pressure regulator on a Pontiac Grand Am?

When did the Pontiac Grand Am stop being made?

The Pontiac Grand Am is a mid-size car and later a compact car that was produced by Pontiac. The Grand Am had two separate three-year runs in the 1970s: from 1973 to 1975, and again from 1978 to 1980. It was based on the GM A platform. Production of the Grand Am was canceled in 1980 when it was replaced by the Pontiac 6000.

https://www.youtube.com/watch?v=hOEhgJe9kH0

How to tell if a fuel filter is bad?

However, this dirty job makes filters especially vulnerable to debris buildups, and once the filter becomes clogged, you will begin to see symptoms as warning signs which need to be attended to immediately. Below are 12 symptoms of a clogged fuel filter and how to tell if fuel filter is bad

Why does my Car Crank and not start?

There are many reasons for your car to crank and not start. Anything from factory security system locking you out, bad fuse/relay, clogged fuel filter,faulty fuel pump, oil sending unit/crank sensor failure, clogged catalytic converter, failing electronic ignition, ECM/PCM,etc.,etc.

Can a bad fuel pressure regulator cause an engine to not start?

It would be wise to check the batteries before considering a failure in the fuel pressure regulator. It is also possible that the engine will not start because of issues in the alternator. There are other potential causes why an engine does not start. One of these is a faulty fuel pressure regulator.

Can a fuel pump be replaced if there is no power?

If there is power, the fuel pump took a dump and needs to be replaced. If there is no power, there is an open in the harness to the pump from the fuse block. This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.

What happens when the fuel pump relay goes bad?

If the fuel pump relay suddenly fails, it will light up the check engine light and store a trouble code on the fuel pressure. The fuel pump relay going bad can affect the fuel pump’s power and affect fuel delivery to the engine.

How much does it cost to replace a fuel pump relay?

Fuel pump relay Replacement cost. The average replacement cost of the fuel pump relay is around $90 and $150. The parts may cost you between $20 and $50, while the remaining cost is the labour cost. Fuel pump relay is a small electronic device which is easily acquired online or at the nearest spare parts shop.

Is there no power to the fuel pump?

No power to the fuel pump and the fuel relay is not getti… Q: No power to the fuel pump and the fuel relay is not getting power. My car has 190000 miles.

What happens when a fuel pump relay goes bad?

If the fuel pump relay has an issue while the vehicle is operating it will cut off power to the fuel pump, which will cause the engine to stall. A faulty relay may allow the vehicle to be restarted a short while later, while a completely failed relay will not.

Why does my fuel pump not prime with the key on?

Fuel pump doesn’t prime with key on. I’ve been trying to figure this out for a couple days now. My 01 Tiburon wouldn’t start the other day. It would crank, but wouldn’t fire. When I turn the key to the “on” position, the fuel pump doesn’t kick on.

Is there a problem with my 2000 Jeep Grand Cherokee?

No one has added a helpful site for this 2000 Grand Cherokee problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: Search CarComplaints.com for these popular complaint phrases…

Usually, when you start your car the fuel pump gives off a slight buzzing sound signaling that it has started working. However, if there is any problem with the fuel pump relay the fuel pump will not respond at all and you will be left turning the ignition key again and again. If you experience such an ordeal, it is time to visit the mechanic.

What are the symptoms of a bad fuel pump relay?

A bad fuel pump relay can cause many different symptoms. Here are the most common ones The fuel pump relay is an important component of the fuel system of your vehicle. The fuel pump relay gives the fuel pump power when it is time to build up fuel pressure in the rail.

What to do if your fuel pump wont start?

For future reference, I had this same problem when replacing the fuel pump on my 2002 s10 4.3L. Searched forever for an answer. It turns out that in order to remove the bed of the truck, you must disconnect the ground for the fuel pump, which attaches in the rear on the drivers side.

Where does the gas go after a fuel pump replacement?

IT SAID GRAY FROM MY OLD HARNESS GOES TO THE SMALL BLACK WIRE TO NEW HARNESS WHICH WAS WRONG !! SO WHEN I REWIRED IT GRAY TO GRAY ! IT PUMPED GAS RIGHT THRU THE FUEL LINE GOING TO THE FUEL FILTER LINE RIGHT AWAY !!

Why does my car shut off when stepping on the gas pedal?

received a Car shuts off when stepping on gas pedal Inspection. Rough idling, frequent stalling, and inconsistent acceleration are all signs that something is amiss with your car. There are a number of systems that can cause this problem.

Why does my car not start when I Turn on the gas?

If the fuel pump is malfunctioning, the engine will be getting less fuel than necessary, which will lead to performance issues, and ultimately cause the vehicle not to start. One of the first signs of a failing fuel pump is hesitation under acceleration.

What should you do if your car runs out of gas?

Sometimes if a vehicle runs out of fuel it can get air in the fuel lines. Any time a vehicle runs out of fuel and more fuel is added, the key should be turned to the ’On’ position then back to the ’Off’ position three or four times to prime the fuel pump.

Why does my Pontiac Grand Prix not start?

WHEN I TURN THE KEY I CAN HEAR CLICKING SOUNDS, BUT IT WILL NOT START. THE WEATHER DOES NOT PLAY A FACTOR IN THIS PROBLEM. I HAVE GAS IN THE CAR, SO THAT IS NOT THE CAUSE. THE CAR WAS TAKEN TO THE DEALER AND THEY COULD NOT PINPOINT THE PROBLEM. WHEN THE CAR STALLS THERE IS NO WARNING.

Can a low pressure fuel system cause spark plugs to wear out?

A low-pressure fuel system will destroy the spark plugs that ignite the fuel in an engine’s cylinder. If by chance you are replacing them and you find they are worn out before their time, you might be looking at a problem with your fuel system.

Can a car run with high fuel pressure?

Gasoline run cars are usually not a huge threat to the environment as they do not emit harmful chemicals from their exhaust. However, if your car starts to excrete thick black smoke from the exhaust after you start it, there is definitely something wrong with the pressure in your fuel system. But in this case, it will be due to high fuel pressure.

How can you tell if your car has low fuel pressure?

You might also hear some spluttering while trying to start your car. If your car’s engine stalls while running or at idle, it is a clear sign you are having some problems with your fuel pressure. This may be due to fluctuations and sudden drops of the fuel pressure.

Why is my GM 3.8L fuel pump not working?

CASE 2: If the fuel pressure gauge registered 35 PSI. This fuel pressure gauge result lets you know that the fuel pump is working and delivering enough fuel to the fuel injectors. The reason your 3.8L GM vehicle is not starting is due to another reason.

How to reset the theft system in a Pontiac Grand Prix?

Enter the vehicle and insert the ignition key into the ignition. Turn the ignition to the “ON” position but do not start the engine. Wait 30 seconds and start the engine. Verify that none of the security lights on the dashboard are flashing or illuminated.

CASE 2: If the fuel pressure gauge registered 35 PSI. This fuel pressure gauge result lets you know that the fuel pump is working and delivering enough fuel to the fuel injectors. The reason your 3.8L GM vehicle is not starting is due to another reason.

What to do if your fuel pump won’t start?

By tapping into the wire that feeds the pump power and making sure it’s feeding the pump with 10 to 12 Volts when your helper is cranking the engine. NOTE: There’s a good chance that anti-theft system on your vehicle is behind the no start problem. For more info, go to: Is the Anti-Theft System Causing the No Start Condition?

If not, there is a bad wire under the fuse block to the battery; it should have constant power at one terminal. Take off the air cleaner and hold the throttle plate open with your hand. Spray some carburetor cleaner into the throttle body. Try to start the car for 2 seconds. If it starts, the fuel pump is the problem.

Do you need a fuel pump pressure gauge?

Owning a fuel pressure gauge is now becoming a must. All vehicles now use an electrical fuel pump to deliver fuel (under high pressure) to the fuel injectors and the best way to diagnose this fuel pump is with a fuel pressure gauge.

What happens if you have a bad fuel pump?

Car Will Not Start. Another more serious symptom of an issue with the fuel pump is a no-start condition. If the fuel pump fails completely — to the point of not being able to provide enough fuel for the engine to run, the vehicle will refuse to start.

What to do if your fuel pump fuse is blown?

Check in your owner’s manual for the location of the fuse box, then find the fuse that corresponds to the fuel pump. Pull it out and inspect it for signs of failure. If the fuse is blown, it will be broken or burned.

When did the last Pontiac Grand Prix fuel pump come out?

The last generation was produced from 2004 to 2008 and had a 3.8 L, 3.8 L supercharged or a 5.3 L engine. Prepare your vehicle for fuel pump servicing. Relieve the fuel system pressure and drain the fuel tank until it is one-quarter full. Disconnect the negative battery cable with a socket wrench.

Is there a way to bypass the fuel pump?

If you put in a computer from a 3.8 non supercharged it runs the pump in performance mode and bypasses it, but you also run very lean and can damage the motor. The part is only $40 it is worth replacing if needed. If you pull the fuel pump relay, bend down tab 85, and put back in it bypasses the fuel pump resistor without changing a fire.

How to install new GM wire harness on fuel pump module?

If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred. Please try again later. (Playback ID: WfYJuntPOgNiQAf9)

Can you replace the fuel pump on a 2002 Pontiac Grand Am?

Replacing the fuel pump on a 2002 Pontiac Grand AM can be done with a set of hand tools, a vehicle jack and a set of jack stands. Doing the repair yourself can save hundreds of dollars in repair bills. Having previous automotive repair experience aids greatly in this process, however, it can be done by a careful and precise novice mechanic.

How do you install a new fuel pump?

Install a new O-ring seal onto the new fuel pump and install the new fuel pump into the tank. Make sure to align the small notch in the fuel tank with the tab on the new fuel pump. Connect the wiring harness to the fuel pump. Replace the fuel tank by lifting the tank up and fastening the strap bolts.

How to test and replace a fuel pump relay?

How to test and replace a fuel pump relay. The principles shown here apply to most vehicles. However, it’s best to check with your vehicle’s repair manual for testing parameters.This specific vehicle is a ’97 Nissan Maxima. — Choosing the best oil filter: Wix XP / Amsoil / Royal Purple..

What causes no start on a GM 3.1L?

I’m going to show you two different methods to verify if the no start condition on your 3.1L or 3.4L GM vehicle is due to a lack of fuel, which usually means that the fuel pump has gone bad. One method involves using just starting fluid and the other involves using a fuel pressure gauge.

How to diagnose a faulty fuel pump failure?

In this video we go over the basic steps of diagnosing a faulty fuel pump. So if your vehicle isn’t starting and you suspect a fuel pump problem, here are some steps to follow to confirm your suspicions. Another ‘quick’ test is to bang on the fuel tank and then try and start the engine.

Why does my 2004 Grand Am GT 3400 not start?

2004 Grand Am gt 3400 v6 and it wont start. The security light isn’t on but its not getting any spark and i cant hear the fuel pump. Fuses and the ignition module isn’t getting juice along with others.

What kind of crank sensor does GM 3.1L use?

Some late model 3.1L and all 3.4L GM V6 engines use two crankshaft position sensors. One crank sensor is called the 3X (or 7X) crank sensor and this bad boy is:

How do you test a GM fuel pump?

GM has made it super easy for you and me to test the fuel pump (with a fuel pressure gauge), since they have installed a fitting (called the Schrader valve) on the fuel pressure regulator to which you and I can connect the fuel pressure gauge to (see photo above).

What is the fuel pressure for a GM 3.1 liter engine?

Fuel Pressure for Later Engines The primary fuel requirement for all other vehicles with the 3.1 liter engine is 41 to 47 PSI. This includes some 1990 A body vehicles, 1990 through 1994 J body vehicles,1991 through 1994 L body vehicles, 1994 N body vehicles, and 1991 through 1994 W body vehicles.

Why does my Car Crank but not get fuel?

IT WILL NOT GET FUEL IN THEFT MODE , WHICH IS WHY YOH GET THE CRANK BUT NO START!!! unfortunately your car either forgot the key , or the key itself took some damage either way just have it relearn the key , put it in the on position , and leave it for 15 mins or so or get a new key and have it programmed , YW Was this answer helpful?

Why does my fuel pump only run for a few seconds?

This sound is the electric fuel pump trying to prime the fuel system. It will only run for a few seconds and then shut off. If you are not sure you could hear it or if there is noise outside; you may have to try it several times. Turn the key on and wait then turn it off.

How to test fuel pump in Jeep Cherokee?

Use a circuit tester and test the harness side for power as your helper turns the key on and off. Remember that there will be power for only 2 seconds, so have your helper cycle the key on and off as you check the terminals, allowing 5 seconds between cycling for the computer to reset.

What to do when your fuel pump wont turn on?

The computer shuts the power off to the pump if it does not see a signal from the crankshaft sensor. Have the helper turn on the key for 3 seconds and off for 5 seconds and on again a couple of times. If the pump cannot be heard, then replace the cap and lift the hood. Check to see if the fuse to the fuel pump is good.

When is the fuel pump relay turned on?

The fuel pump relay is an important component of the fuel system of your vehicle. The fuel pump relay gives the fuel pump power when it is time to build up fuel pressure in the rail. Whenever you turn on the ignition of your vehicle, the fuel pump relay is turned on. There are different reasons due to which the fuel pump relay fails.

Can a 20 amp fuse cause a blown fuse?

The most common amperages are 15, 20 and 30, and replacing a 15 amp fuse with a 20 or 30 amp, or a 20 amp fuse with a 30 amp, may result in a blown fuse. Worse, it could cause a more severe car electrical problem, because it can cause wires to melt.

How can you tell when your fuel pump is not working?

The pump itself is usually located inside the gas tank. There are a handful of symptoms to look out for that could indicate a problem with the fuel pump: Slow startup: If the engine takes a while to turn over once the key is turned in the ignition, the fuel pump may be having an issue getting enough fuel to the engine.

Consequently, if the fuel pump relay has an issue, it will cut off power to the fuel pump. Also, if a relay overheats, the electrical contacts inside the relay can short circuit; causing the electrical flow to stop. However, when the relay contacts cool, it will resume the flow of electricity.

When did the fuel pump in my van fail?

The fuel pump failed 7 days after it was installed. The van died going up a hill in my apartment complex and never started again. I had to roll it backward into a parking place in a public area by the mailboxes. The apartment complex was not happy.

Navigation