What should I do about my Hyundai Elantra brake problems?

Additionally, if you have had any rear brake work done on your vehicle that required removing the rear rotors or emergency/parking brake work done; more than likely…the service technicians did not repair it correctly…not repairing or making adjustments to your vehicle according to Hyundai Official Repair/Service manuals.

Which is the worst year for Hyundai Elantra?

The worst problem for the Hyundai Elantra is the engine, with the 2013 model having the most overall complaints, and also being rated as the worst model year due to the severity of problems, the average repair cost, and the time of the onset of issues.

Why does my Hyundai Elantra not have a push pull gauge?

OWNERS SHOULD CHECK THEIR ON-LINE MANUAL FOR THE EXACT DETAILS. Why they do not have the tool, look at the ESSENTIAL SERVICE TOOL SURVEY FOR 2008 (on line) not a listing for a force push/pull gauge anywhere.

Replace front brake pads and both seized calipers. Front Caliper Slide pins with rubber bushing (sleeve) had to be replaced due to corrosion and swelling of the rubber rubber bushing. ETC light on intermittently. Dealer replaced brake switch. Bad master cylinder. Brake pedal went the the floor slowly and was spongy. But still braking…

What does ESC off warning light mean on Hyundai Elantra?

‘ESC OFF’ light went on intermittently – dealer replaced brake switch under warranty. ESC would intermittently turn off and require the car to be turned off and back on to reset. Dealer replaced the brake pedal switch to resolve the problem. ESC OFF warning light turning on and off intermittently.

What kind of engine does a Hyundai Elantra have?

Driving the Used 2007 Hyundai Elantra. Zippy little engines are no longer a surprise in economy cars, but the SE’s 2.0-liter, 4-cylinder, 138-horsepower CVVT ULEV engine, teamed with the five-speed transmission, is particularly impressive, especially on uphill climbs.

What kind of airbags does the Hyundai Elantra have?

If safety is your issue, the Elantra offers front, side-impact and side-curtain airbags, plus antilock brakes (ABS), as standard equipment. You may not like this car if your daily drive demands constant gear shifting, as the SE’s five-speed manual transmission tends to be notchy. What’s New?

Is the Hyundai Elantra a good car to buy?

Challenging competitors for price, value and quality, the Elantra has a new chassis, many appealing features as standard equipment and it’s included on the “Greenest Vehicles of 2007” list of the American Council for an Energy-Efficient Economy (ACEEE)

Are there any problems with the 2011 Hyundai Elantra?

The 2011 Hyundai Elantra has 572 problems & defects reported by Elantra owners. The worst complaints are engine, fuel system, and transmission problems.

Why is my Hyundai Elantra engine stalling out?

This can be caused by the fuel pump or fuel filter. If your Hyundai Elantra’s engine timing is off, it’s going to stall out, misfire, and altogether not run properly. Here are some of the more common causes of an engine timing problem: VVT Problem – Many modern engines are equipped with Variable Valve Timing.

The 2011 Hyundai Elantra has 572 problems & defects reported by Elantra owners. The worst complaints are engine, fuel system, and transmission problems.

The Hyundai Elantra is a decent car that gets better with every new generation. While the newest models have the best features, an older Elantra can also be a good buy with proper care and maintenance.

What to do if you have a brake leak in your Hyundai Sonata?

Replace the master cylinder if there is a difference in pedal stroke. Look for damage or signs of fluid leakage. Replace the brake hose with a new one if it is damaged or leaking. Check brake operation by applying the brakes. Look for damage or signs of fluid leakage.

Are there any problems with the Hyundai Elantra?

Hyundai Elantra owners have reported 8 problems related to brake abs warning light (under the service brakes category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Hyundai Elantra based on all problems reported for the Elantra.

Why does my Hyundai Elantra not have a parking brake?

Skipping these procedures could lead to emergency/parking brake drag when the brake lever is not set or the parking brake not functioning when you believe you have set the emergency/parking brake. Step 1. Block the front tires so the vehicle will not roll. Step 2. Raise the vehicle as if you were going to change the drivers side rear tire.

Why is the ABS warning light on on my Hyundai Elantra?

See all problems of the 2012 Hyundai Elantra . The abs warning light was noted to be on continuously for more than a week. The problem was traced to a broken wire in the main engine harness. There was no noticeable change in performance of the vehicle.

What kind of brakes do I need for my Hyundai?

Here at Hyundai OEM Parts Online, we have all of the genuine OEM brake parts you need for your vehicle below! Description: Santa Fe. Disc brakes. Description: Drum brakes. Description: Accent. Disc brakes. Description: Accent. Drum brakes. Description: Accent.

Is it safe to repair your brake lines?

You might consider repairing your own brake lines but are afraid that you’ll compromise your vehicle’s safety. No need to worry. This video will take you through all the steps necessary to perform the repair easily and safely. It’s as easy as replacing brake pads. The parts used in this video can be found at your local auto parts store.

Why is my brake light not working properly?

Brake light switch does not work properly with the ESC, Consequence the ESC OFF light came on when driving. Intermittent ESC light, faulty brake switch replaced. ESC light came on again. Brake light switch replaced again, steering angle sensor ordered. Steering angle sensor/clockspring unit replaced under warranty (related to ESC light).

How to repair right rear brake on Hyundai Elantra?

Loosen the right-rear brake bleed screw (A) to allow air to escape from the system. Then tighten the bleed screw securely. 4. Repeat the procedure for wheel in the sequence shown below until air bubbles no longer appear in the fluid. 5. Refill the master cylinder reservoir to MAX (upper) level line. Brake Booster.

What to do if your brake system does not work?

Check brake operation by applying the brakes during a test drive. If the brakes do not work properly, check the brake booster. Replace the brake booster as an assembly if it does not work properly or if there are signs of leakage.

Where are the brake caliper guide pins located?

To fix this, you have to remove the brake pads and clean the brake pad bracket with a file or sandpaper and lubricate it with copper paste or something similar. The brake caliper guide pins are located at the brake caliper bracket and help the caliper to slide forward and backward when you are braking.

What happens when you have a problem with your brake calipers?

Whenever you have issues with the brake calipers, you will have problems stopping the car. This can be dangerous, especially when you are traveling at high speeds. The brake calipers have pads attached to them that clap on the wheel rotors.

What happens when you replace the right caliper on a car?

However, if the replacement right caliper allows air into the system past the caliper piston seal each time the brakes are released, this air accumulates in the right caliper depending how often the brakes are applied and released. Have a NEW not a rebuilt right caliper installed. Tester GSragtop July 6, 2016, 2:45am #7

What causes a brake caliper to stick to the pedal?

Caliper slides are grooves within the brake caliper that hold the brake pads when you press the brake pedal and let the pads loose when you let go of the pedal. However, with time the shims have an accumulation of debris and this causes them not to hold the brake pads tightly. This will cause the brake calipers to stick.

How much does it cost to replace a brake caliper on a Hyundai Elantra?

Hyundai Elantra Brake Caliper Replacement costs $318 on average. What is the Brake Caliper all about? Most cars come with disc brakes in the front, and many models also have disc brakes in the rear. A caliper is part of the disc brake system. When you press the brake pedal, the brake fluid flows from the master cylinder to the calipers.

What kind of brake pads do Hyundai Elantra use?

Hyundai Elantra / Elantra Coupe with D1595 Brake Pads 2013, Front Disc Brake Caliper Piston by Carlson®. If the finish of the caliper piston is damaged, the piston can’t slide smoothly causing a caliper sticking problem. To restore… Hyundai Elantra 2013, Disc Brake Caliper Repair Kit by Centric®.

Where is the brake bleeder screw on a Hyundai Elantra?

Hyundai Elantra 2013, Brake Bleeder Screw Set by Carlson®. A brake bleeder screw is normally mounted at the highest point on each cylinder or caliper and used to release air and old brake fluid from the brake system. When it comes to… Hyundai Elantra 2013, Disc Brake Caliper Guide Pin Boot Kit by Carlson®.

What should I do if my brake caliper goes bad?

Caliper servicing is usually done as part of a brake service job. Work on brake calipers would likely include new brake pads because if the calipers have gone bad, it is very likely that the brake pads are worn out. Remove and replace brake caliper and pads. Inspect brake rotors. Inspect brake line hoses. Replace brake fluid.

Why is the brake pull on my car not working?

Either one of the calipers is not actuating or one of the calipers is stuck on. This can be due to the caliper slides are not working or a brake hose has fallen apart internally not allowing the brake fluid pressure to go into or come out of the caliper.

What to do when you have a brake pull?

When these sides become stuck (seized) the caliper will either not fully engage or release creating a brake pull. An easy way to check this is too take the car for a drive while using the brakes heavily. Then use an infrared laser temperature reader to rear the temperature of each rotor.

Are there any problems with the 2013 Hyundai Elantra?

Elantra owners have tried sensor adjustments, wheel alignments, even replacing axles, most with no luck. Hyundai has made vehicle buybacks through arbitration, but that rarely works out well financially for owners in the end. Also there is a pattern of complaints about the 2013 Elantra brakes grinding at very low mileage.

Why does my Hyundai Elantra not turn the wheels?

If you’ve broken a drive/axle shaft, your Hyundai Elantra’s transmission has no way to turn the wheels anymore. If this were the case, there would not be any movement whatsoever from the vehicle. You also wouldn’t feel the slight jerk your Elantra as you put it into gear.

How do you replace the front tire on a Hyundai Elantra?

Replace both front tires, then screw on and tighten all of their lug nuts. Slide the jack back under the front of the car’s suspension and jack it up so that it lifts off the jack stands an inch or two. Pull the jack stands out, then slowly lower the car back to the ground.

Where is the floor jack on a Hyundai Elantra?

Slide the floor jack under a solid part of the suspension on the front end of the car. Carefully jack the car up until it is high enough for you to be able to slide jack stands under the front axle.

How do you replace brake pads on a Hyundai Elantra?

Try to pull the old brake pads out of the caliper mount by hand. If they’re stuck to the rotor, which is fairly common, use the screwdriver to pry them off and then remove them. Slide the new brake pads into the caliper mount in the same way the old ones were installed.

How many miles does a Hyundai Elantra last?

With proper care and maintenance, it’s probably safe to assume that barring catastrophe, Your Elantra will last for upwards oF-150,000 miles. With preventative maintenance, top quality fluids, and nonaggressive driving, You’re probably looking at close to 250,000. Add in a little luck to the previous, and You too could join the 300,000 mile club.

Slide the floor jack under a solid part of the suspension on the front end of the car. Carefully jack the car up until it is high enough for you to be able to slide jack stands under the front axle.

What causes no brake fluid to come out when bleeding?

Flex hoses deliver brake fluid from reservoir and brake master/cylinder to the brake caliper. In case the hoses happen to have any cut, or it’s torn out, there will be no pressure in the brakes; thus, brake bleeding will fail. It also causes the brake fluid to leak.

What do you need to know about bleeding ABS brakes?

Here’s what you need to know about Bleeding ABS brakes. ABS systems are VERY sensitive to air bubbles. You know that air rises in the system. Once a bubble gets into the ABS valves, it’s almost impossible to suck it back down even with a hand-held vacuum pump. It’s definitely impossible to do it just by pumping the brake pedal.

What happens to the brake piston when you let it off?

When the brakes are applied, the brake piston seal is deformed slightly. When the car drivers let the brakes off, they uncoil and help to compress the pistons for drag-free running. If the piston fails to slide adequately on the seals, then the seal impedes the piston from permanently compressing. 3. Inactivity of the Vehicle

Why do I feel trapped in the brake line?

While driving it will feel as if the brake pedal is spongy, however, the brakes will also take longer to stop the vehicle. This situation calls for an immediate inspection of the brake system. When air enters the brake lines, it typically becomes trapped due to the fact that brakes are hydraulically controlled.

Why do I feel grinding in my brake pedal?

Grinding that you also feel in the pedal could mean a number of things. There could just be some gravel or a rock caught in the caliper unit, easily remedied. But you may have gone too long without brake servicing.

What happens when you hit the brake pedal?

When you hit the brake pedal, the brake pads hug the rotors, slowing them and your vehicle. You want rotors to be smooth and completely even in thickness. Over time and thousands of wheel revolutions, it’s normal for the rotor surface to get slight variations. Rust can also sometimes develop.

When did the Hyundai Elantra clutch go bad?

Consumer Hyundai Elantra clutch failed while driving. Consumer had vehicle towed to dealer where they told consumer that it was not included in warranty. The primary reason the consumer purchased the vehicle was for it’s 10 year/100000 mile warranty. Vehicle was undrivable when clutch went bad without any warning at about 13,900 miles.

What was the problem with the 1996 Hyundai Elantra?

See all problems of the 1996 Hyundai Elantra . Clutch slave cylinder failed. If the drivers foot accidently slips off of the clutch pedal, the clutch is totally unresponsive until it’s pumped numerous times. Sometimes the clutch would not return to the original position after being applied while driving.

How long is the warranty on a Hyundai Elantra?

Supposedly the warranty on the clutch is only for 12 months or 12000 miles. Ak. Consumer was traveling on the interstate about 70 mph, applied the brakes and enganged the clutch, experienced complete clutch failure. Consumer has contacted the dealer, dealer aware of problem, parts were replaced.

What’s the RPM on a 2013 Hyundai Elantra?

Summary: while 2013 Elantra is in park, rpm’s rest at 5,000. While in drive, rpm”s bottom out at 2,500-3,000, disallowing the ability to naturally stop. This issue appears to reside in the accelerator pedal and the components located therein. This is to be confirmed at a Hyundai service center.

Hyundai Elantra owners have reported 35 problems related to cruise control (under the vehicle speed control category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Hyundai Elantra based on all problems reported for the Elantra.

What happens when you set cruise control on a Hyundai Elantra?

If you set cruise control, the rpms will jump by 500 or more. The jump in engine speed is maintained, not temporary. The sustained increase in engine speed will reduce fuel economy and increase mechanical wear on the vehicle. This issue has been present since the vehicle was purchased brand new.

Navigation