What does p0134 mean on Honda O2 sensor?

What does p0134 mean on Honda O2 sensor?

P0134 is a relatively common OBDII trouble code. It’s generic, which means that it has the same meaning for any vehicle with OBDII. It means that the PCM/ECM is not detecting any activity from the sensor.

What is the oxygen sensor code on a Honda Civic?

The codes were P0135 and P0134. It seemed like my upstream oxygen sensor NTK 24425 was only an oxygen sensor, but not an air-fuel oxygen sensor. So I got an upstream Denso 234-9005 air fuel ratio oxygen sensor and the hesitation is gone and the car runs smooth. However, the P0134 (bank 1 sensor 1, no activity) check engine light is still on.

What does no activity mean on Honda Civic?

P0134 is a relatively common OBDII trouble code. It’s generic, which means that it has the same meaning for any vehicle with OBDII. It means that the PCM/ECM is not detecting any activity from the sensor. The Civic’s computer uses the oxygen sensor to measure the amount of O2 gases in the exhaust.

What does Bank 1 mean on a Honda Civic?

Bank 1 is the side of the engine that has the first piston in the firing order. That means that different model years and engine can have Bank 1on a different side. If it’s an inline engine (almost all 4 cylinder motors), you don’t need to worry about which side it’s on, since there’s only one exhaust manifold.

What should I do if my Honda sensor says p0134?

If the sensor circuit is OK, and the DTC (s) come back after clearing them and doing a short test-drive, replace the A/F sensor. The replacement A/F sensors in Honda parts stock are an improved version over the original sensor. The cost to diagnose the P0134 HONDA code is 1.0 hour of labor.

What does the code p0134 on the ECM mean?

Code P0134 is triggered when your vehicle’s O2 sensor (bank 1, sensor 1) is malfunctioning. The Engine Control Module (ECM) detects that the Oxygen (O2) sensor is at a standstill and is not accurately reading the amount of oxygen in the exhaust.

The codes were P0135 and P0134. It seemed like my upstream oxygen sensor NTK 24425 was only an oxygen sensor, but not an air-fuel oxygen sensor. So I got an upstream Denso 234-9005 air fuel ratio oxygen sensor and the hesitation is gone and the car runs smooth. However, the P0134 (bank 1 sensor 1, no activity) check engine light is still on.

P0134 is a relatively common OBDII trouble code. It’s generic, which means that it has the same meaning for any vehicle with OBDII. It means that the PCM/ECM is not detecting any activity from the sensor. The Civic’s computer uses the oxygen sensor to measure the amount of O2 gases in the exhaust.

What does O2 mean on a Honda Civic?

Honda Civic P0134: O2 Sensor → No Activity Detected B1S1. P0134 is a relatively common OBDII trouble code. It’s generic, which means that it has the same meaning for any vehicle with OBDII. It means that the PCM/ECM is not detecting any activity from the sensor.

Why is the O2 sensor on my Honda Civic not working?

Bad O2 Sensor – The oxygen sensor itself can go bad. This is often the cause of P0134. Replacing it without testing the wiring going to/from it first is a gamble that will often pay off, but it’s still a good idea to check your harness connections and inspect it first.

How to diagnose Honda engine OBDII code p0134?

If the sensor circuit is OK, and the DTC (s) come back after clearing them and doing a short test-drive, replace the A/F sensor. The replacement A/F sensors in Honda parts stock are an improved version over the original sensor. The cost of diagnosing the P0134 HONDA code is 1.0 hour of labor.

Honda Civic P0134: O2 Sensor → No Activity Detected B1S1. P0134 is a relatively common OBDII trouble code. It’s generic, which means that it has the same meaning for any vehicle with OBDII. It means that the PCM/ECM is not detecting any activity from the sensor.

Bad O2 Sensor – The oxygen sensor itself can go bad. This is often the cause of P0134. Replacing it without testing the wiring going to/from it first is a gamble that will often pay off, but it’s still a good idea to check your harness connections and inspect it first.

Posted In Q&A