How do you take the back seat out of a Honda CRV?
Locate all the retaining bolts holding the CRV’s rear seat to the floor. Tilt the seat forward and remove the retaining bolts with a socket wrench. Pull the seat forward and away from the bolts. Climb out of the CRV and pull the seat out through the open door. Be careful not to scratch the car while you’re pulling the seat out.
How to remove a brake drum that is stuck on?
Watch how to remove a brake drum that is stuck on. I go through the steps so anyone can remove their drum brake. In this case the drum adjuster was stuck so first try to get it off by wiggling back and forth. Then spray penetrating oil to remove rust between the drum and the seat. Then hit it with a hammer hard.
What happens when you change the drum on a car?
Most drum brakes on cars and other common vehicles are hydraulically powered. If there is a leak in the hydraulic system, you may notice fluid inside the drum and on the brake shoes. Usually, this is accompanied by decreased brake performance. If necessary, replace the leaky wheel cylinder.
What to do if your drum adjuster is stuck?
In this case the drum adjuster was stuck so first try to get it off by wiggling back and forth. Then spray penetrating oil to remove rust between the drum and the seat. Then hit it with a hammer hard. This should free the drum if it is just rusted on.
What’s the best way to remove a brake drum?
Use a screwdriver to attach the brake drum puller’s screw tightly. Tighten the screw until the brake drum puller is securely fastened around the brake drum. Do not over-tighten the screw on the brake drum puller. Knock the back of the brake drum lightly with a hammer. Tap the hammer against the brake drum with an outward motion.
Most drum brakes on cars and other common vehicles are hydraulically powered. If there is a leak in the hydraulic system, you may notice fluid inside the drum and on the brake shoes. Usually, this is accompanied by decreased brake performance. If necessary, replace the leaky wheel cylinder.
How do you adjust the rear drum brake on a jeep?
Pull the adjuster lever downward and then unhook it from the adjuster lever pin attached to your Jeep’s brake shoe. 8. Unhook the brake shoe adjuster cable from the adjuster lever and set it aside. 9. Using a pair of vice grips, clamp onto the brake shoe return spring attached to the forward facing brake shoe and then pull it off the anchor pin.
What should I do about my Pontiac Vibe brake drum?
My husband has a 2005 Pontiac Vibe. He took the Brake Drum off and at some point had our nephew step on the brake. Well after doing that he figured out that the brake drum will no longer go on and we can not find anything that states what to do. We have tried moving the Adjuster, but to no avail. Please help! helpful?
How do you remove transmission nut on Honda CRV?
Remove the cotter pin on the bottom of the ball joint. Loosen this nut by about 1/4″, but do not completely remove it. Jam your ball joint removal tool between the control arm and your wheel hub, grab your hammer, and proceed to beat it like a rental car. This usually takes a substantial amount of effort.
How to replace AC compressor in Honda CRV?
The video’s are intended for information only. Follow the manufactures repair procedure and use appropriate safety procedures . Email [email protected] Jimthecarguy Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.
How do you repair a Honda Civic seat?
Tilt the seat forward and remove the retaining bolts with a socket wrench. Pull the seat forward and away from the bolts. Climb out of the CRV and pull the seat out through the open door. “Chilton’s Honda Civic & CR-V 2001-06 Repair Manual”; Robert Maddox; Haynes Publishing Group; 2007.
Can a Honda CRV front suspension be replaced?
Replacement of the Honda CRV front suspension Strut, Lower Ball Joint and Control Arm and the Sway Bar / Stabilizer Bar link. This constitutes all the components that comprise the front end of the Honda CRV.
Locate all the retaining bolts holding the CRV’s rear seat to the floor. Tilt the seat forward and remove the retaining bolts with a socket wrench. Pull the seat forward and away from the bolts. Climb out of the CRV and pull the seat out through the open door. Be careful not to scratch the car while you’re pulling the seat out.
How do you remove a transmission from a Honda CRV?
The best way to remove the electrical connectors is NOT to break the tabs on them with a screw driver. Instead, use your meaty hands to squeeze the tab until it clicks, then stick a flatblade screwdriver between the two connectors and twist. Most of the connectors will be pretty seized up.
Tilt the seat forward and remove the retaining bolts with a socket wrench. Pull the seat forward and away from the bolts. Climb out of the CRV and pull the seat out through the open door. “Chilton’s Honda Civic & CR-V 2001-06 Repair Manual”; Robert Maddox; Haynes Publishing Group; 2007.