Where is the turn signal module on a Street Glide?
Jonathan, sounds like you have a bad turn signal module. You will find this module between the fuel tanks, beneath your dash area. Thanks, and good luck Similar Question Been enjoying the videos and tips I have a 2008 Street glide with 90K miles on it. I always took it to the dealer until I found your website and got the premium membership.
Why is my left turn signal not flashing?
When it’s not working, there is no signal front & rear and no signal indicator either. When working, both markers function properly as does the indicator. With new bulbs installed and sockets cleaned, I’ve narrowed the problem down to either the left turn signal switch or the turn signal module.
Why are the turn signals on my hog not flashing?
Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work
Why is my turn signal not flashing on my Fatboy?
Had the same problem on a 99 Fatboy changed the ignition switch and problem was solved Have a 97 FXDWG. Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly.
What causes a constant on condition on a Speedo?
You can search for codes in your speedo head. The wrong bulb will cause a constant on condition as well. I bought a used soft tail springer that the previous owner had put an AutoZone bulb in one of the rear turn signals. The correct H-D bulb with the correct resistance fixed the issue cheaper than a module.
Jonathan, sounds like you have a bad turn signal module. You will find this module between the fuel tanks, beneath your dash area. Thanks, and good luck Similar Question Been enjoying the videos and tips I have a 2008 Street glide with 90K miles on it. I always took it to the dealer until I found your website and got the premium membership.
How to install a load blinker on a Harley?
To install you take off saddle bag and side cover, or for mine had to pull off the seat and find the wiring harness that goes to the rear of the bike and unplug that harness and plug this into it! Very easy to do! This item did not resolve all the issues created from swapping incandescent turn signals to LED on my HD ’08 Road King.
Why is my turn signal on on my Dyna Glide?
Diagnosing and clearing the codes on each module is really simple, as explained below. Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse.
How can I tell if my turn signal module is faulty?
You can pretty much determine if the module is faulty by following the troubleshooting steps outlined in the manual. If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled.
Where is the turn signal module on a 91 heritage?
91 heritage FLSTC. Anyone have a pic or a good description as to where the turn signal module is mounted on this bike? Any wiring harness mounting or routing pics would be helpful in reassembling this basket case of mine. Thanks! Click to expand…
Where is the turn signal mount on a Harley Davidson?
Click on OEM parts finder tab. Try this website. Microfiche for most Harley’s avaiable. Click on OEM parts finder tab. Click to expand… Looked there already in an attempt to help the OP. Had some info but not complete for the 91 FLSTC. Now where’s the starter relay mount? Click to expand… Up by the battery under the seat.
Where is the Flasher located on a Harley Davidson?
Just looked it up…It`s mounted on a bracket on the frame, up near the steering neck. The `90 and earlier have the flasher unit mounted in that location along with the circuit breakers.
Find the orange wire that feeds 12 volts to your turn signal module. Power it off of a breaker that is powered on, both 1 & 2 “clicks”. My speedometer is working erratic. When I give it throttle the speedimeter digital reading goes blank and the engine light comes on and the turn signals will not flash. When I come to a stop they work
Had the same problem on a 99 Fatboy changed the ignition switch and problem was solved Have a 97 FXDWG. Installed a badlander load equalizer 17 years ago for run and brake lights on the rear. If the bike is not moving the right turn signal functions correctly.
When it’s not working, there is no signal front & rear and no signal indicator either. When working, both markers function properly as does the indicator. With new bulbs installed and sockets cleaned, I’ve narrowed the problem down to either the left turn signal switch or the turn signal module.
Diagnosing and clearing the codes on each module is really simple, as explained below. Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse.
How does the turn signal on a Harley Davidson work?
The Turn Signal Security Module monitors the signals and the alarm system for the bike. When there is a problem, the red light key will illuminate. Diagnosing and clearing the codes on each module is really simple, as explained below.
How do you close the Diagnostic Code on a Harley Davidson?
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes.
What does the MAP sensor on a Harley Davidson do?
MAP – manifold Absolute Pressure sensor. The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. The EMC then adjusts the spark and fuel-timing advance curves for optimum performance. VSS – Vehicle Speed Sensor.
Why are my turn signals not working on my Harley Davidson?
Changes in temperature, moisture and dust are some of the factors that can cause this to happen. Our bikes need some attention after spending a lonely cold winter in the garage.
Why is my hazard light not working on my Harley?
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.
Are there brake lights, turn signals or cruise?
Discussion in ‘ Touring Models ‘ started by TXViper, May 19, 2009 . I have a 2009 Street Glide and just had the horn, cruise, turn signals, and brake light all quite working. I don’t have any blown fuses, and the turn signals still flash when I turn the ignition off indicating that the security system is activated.
Changes in temperature, moisture and dust are some of the factors that can cause this to happen. Our bikes need some attention after spending a lonely cold winter in the garage.
Why is my horn not working on my Harley?
I do not think you have a horn relay, so very little to go wrong. Common problem is blown fuse or horn is temperature sensitive, as it is simply a electromagnet with bimetallic strip interrupter that makes and breaks rapidly the magnetic field buzzing the metal diaphram.
Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.