When to install brake controller on GMC Sierra?
When you install a brake controller on a 2007 (new body style) through 2013 GMC Sierra or Chevy Silverado, you will have additional wires under the hood which make the installation slightly different from a typical installation. The following will take you through step-by-step through this installation process.
What kind of brake control does a Chevy Silverado use?
TEKONSHA P3 BRAKE CONTROL + WIRING HARNESS FOR 03-06 CHEVY SILVERADO, GMC SIERRA, SUBURBAN, TAHOE, YUKON, DENALI, HUMMER. CONTROLLER + PLUG/PLAY WIRE KIT.
Where is the ring terminal for the brake controller?
The ring terminal for brake controller power is located directly to the right of the power distribution box. It is taped to a wire harness between the driver-side front fender and the power distribution box. Cut the tape to release it from the harness.
What’s the replacement socket for a brake controller?
With the square knockout panel removed, slide the 7-way replacement socket (PK11916) into the knockout hole. Line up the notches on the replacement socket with the notches in the knockout hole.
When you install a brake controller on a 2007 (new body style) through 2013 GMC Sierra or Chevy Silverado, you will have additional wires under the hood which make the installation slightly different from a typical installation. The following will take you through step-by-step through this installation process.
TEKONSHA P3 BRAKE CONTROL + WIRING HARNESS FOR 03-06 CHEVY SILVERADO, GMC SIERRA, SUBURBAN, TAHOE, YUKON, DENALI, HUMMER. CONTROLLER + PLUG/PLAY WIRE KIT.
Where is the brake control box on a 1999 Chevy?
This junction box (shown below) is located on the driver’s side below the dash, left of the brake pedal. If the factory brake control adapter cannot be found, we offer a replacement (for model years 1999-2002 use 3025-S, for years 2003-2006, including 2007 Classic models use 3015-S).
How to replace brake control switch on GM Truck?
Just removed two Phillip-head screws to loosen dash panel beneath steering column, then easily pried with screwdriver the panel off, unplug connector, bent tabs holding in brake controller, slide out, slide new one in and secured with tabs, re-installed connector, re-installed panel.
Are there any brakes on my GMC 2500?
I have a 2009 2500 GMC with factory intergrated trailer brake system. I was getting “service trailer brake” message and found that the plug in the rear of the truck was full of water. I dried the plug out and now I have no trailer brakes. All of the lights and turn signals work, but no brakes.
What kind of trailer brakes do GMC trucks have?
I have a 2009 2500 GMC with factory intergrated trailer brake… I have a 2009 2500… I have a 2009 2500 GMC with factory intergrated trailer brake system. I was getting “service trailer brake” message and found that the plug in the rear of the truck was full of water. I dried the plug out and now I have no trailer brakes.
Is there a Factory Brake Controller for a Silverado?
The truck is a 2008 chevy silverado 2500HD with a factory controler. With a proportional type trailer brake controller like better aftermarket units such as the P3 # 90195 and most factory units there will be no output with the vehicle at rest unless you press the manual override lever.
Where is the brake controller plug in harness on a GMC Sierra?
On your 2009 GMC Sierra that is equipped with a tow package, the wiring to install a brake controller is already ran from the factory and a plug-in adapter is not needed. You will find a bundle of wires below the dash to the left of the brake pedal. The wires should be taped up and tucked up and out of the way.
The truck is a 2008 chevy silverado 2500HD with a factory controler. With a proportional type trailer brake controller like better aftermarket units such as the P3 # 90195 and most factory units there will be no output with the vehicle at rest unless you press the manual override lever.
What makes OEM GM brake pads so good?
OEM GM brake pads are specifically made from quality materials and with quality engineering so that they will withstand the friction your GM will put on them. OEM GM brake pads are built to last as long as the original pads. If you want to keep your brakes in top condition, regularly check your pads for wear and replace them with OEM GM brake pads.
What was the problem with my Duramax trailer brakes?
My truck (08 2500HD duramax) was going to go off warranty soon so I had the dealer look at it. The said a pressure sensor in the master cylinder that provides the voltage output based on pressures to the trailer brake control was dead. They replaced it and power bled the front brakes.