How to reset the SRS warning light by yourself?
Step 8: You should hear beeps for 3 seconds, and when the beep is gone, the SRS should turn OFF. Step 9: QUICKLY, Take the paperclip/wires out and the light should come back on. Step 10: When the light comes on, QUICKLY plug the paperclip back in to complete the curcuit again, in a second or so, the SRS light should TURN off
Why is my SRS light not working on my Honda Accord?
Tried the battery thing, the MES plug light reset and basically nothing works, Most cheap scanners including the Snapon Solus-Pro won’t read air bag .or abs codes.
What does the SRS light on a car mean?
When you see the Supplemental Restraint Systems (SRS) light illuminated on the control panel of your Vehicles it means there is a problem with the airbags or the seatbelt tensioners. When there is a malfunction in the Vehicles codes are stored in the On-Board Diagnostics (OBD) computer.
How do you reset the SRS light on a Honda CRV?
Put the key in the ignition and turn it on, but don’t start the engine. Keep the ends of the wire touching while you do this. The SRS light will flash on, and then disappear. Separate the wires immediately. The SRS light should come on again. Repeat Step 3 and the SRS light will blink twice and turn off.
Why is my SRS warning light not reset?
And in other situations, SRS light on caused by Supplemental Restraint System Trouble.You need to repair the trouble firstly,and then reset the SRS light.If not,you will find the SRS light can not be reset,even you try to repeat the guide again and again.
Where to reset the SRS light on a Mercedes?
Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car. Find the port that fits the OBD cable and plug the scan tool’s cable into this port. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts.
When you see the Supplemental Restraint Systems (SRS) light illuminated on the control panel of your Vehicles it means there is a problem with the airbags or the seatbelt tensioners. When there is a malfunction in the Vehicles codes are stored in the On-Board Diagnostics (OBD) computer.
Where is the fuse for the SRS light?
In most models, this is fuse #40, located in the lower right corner of the fuse block. Turn the ignition switch to “ON” without starting the engine. Leave the ignition on for about one minute to allow the system a chance to reset. Turn the ignition off.
Where is the reset SRS light on a Mercedes Benz?
Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car.
Why does the airbag warning SRS light come on?
The airbag warning SRS light could come on due to a defective Child Seat Occupancy Recognition Sensor which is installed in the passenger seat. If you had an auto mechanic diagnose the car or if you scan the airbag module yourself using Launch Creader VII Diagnostic Scanner you will find one of the following errors:
What does SRS stand for in Mercedes Benz?
In this video, we will show you how to use the iCarsoft i980 to reset the SRS on Mercedes-Benz cars manufactured after 1996. What does SRS light mean? SRS stands for Supplemental Restraint System.
Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car.
What does it mean when SRS warning light stays on?
SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system. It is very unlikely that your airbags are going to deploy randomly, but the concern is that they may not deploy…
Which is the best scanner to reset the SRS light?
Our favorite scanner that will read and reset your SRS / airbag light is the iCarsoft i980 for Mercedes-Benz which will retrieve the SRS light but also the check engine.
How to read and reset SRS / airbag light?
Battery dying. How to read and reset SRS/ Airbag light? Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it.
Step 8: You should hear beeps for 3 seconds, and when the beep is gone, the SRS should turn OFF. Step 9: QUICKLY, Take the paperclip/wires out and the light should come back on. Step 10: When the light comes on, QUICKLY plug the paperclip back in to complete the curcuit again, in a second or so, the SRS light should TURN off
What does the SRS light mean on a Mercedes Benz?
What does SRS light mean? SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system.
Why does the SRS light come on when an adult is in the seat?
This tells the SRS to fire the passenger airbag if an adult is in the seat. If this sensor is not working properly, it can cause the warning light to illuminate. Solution: Check that the wiring connector is secure, the wiring is intact and the seat sensor is operational.
Why does the SRS / airbag light stay on?
Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Install a new battery; Reset SRS/ Airbag light.