Is there a trouble code on the speedometer?
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Trouble codes are read via the odometer.
What does the Code 02 mean on a Harley Davidson?
If it were a current code, the light would remain lit while running. Above codes can also be set if 02 sensor fails. CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.
What does the trouble code p0217 stand for?
P0217 This Trouble Code sets if the Engine Temperature indicates a Severe Over Temperature Condition. Can be caused by any failure that would cause the engine to overheat. This Trouble Code Does Not indicate a problem with the Engine Temperature Sensor. 15 P1116
Is the speedometer capable of displaying a DTC?
The IM (instrument module) is capable of displaying DTC’s (diagnostic trouble codes). Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC).
What does a blinking D4 transmission light mean?
keith July 6, 2016, 3:00am #2 A blinking D4 light is like a check engine light for the transmission. Regular code readers like the ones used by AutoZone will not read the transmission codes. You will need to take the vehicle to a dealer or a trusted transmission repair shop.
Why does my Honda D4 flash p1768 code?
It can be from low fluid level to dirty trans fluid, a shift solenoid and even the linear solenoid the p700 code pretty much pops up anytime the d4 flashes and p1768 is the linear solenoid , now on this CR-V i changed the linear solenoid and it still wouldnt clear the code so i swapped the ecu which is the tcm in this unit and no more flashing d4
What does a blinking D4 light on a Honda Accord mean?
A blinking D4 light is like a check engine light for the transmission. Regular code readers like the ones used by AutoZone will not read the transmission codes. You will need to take the vehicle to a dealer or a trusted transmission repair shop.
What are the colors of the D4 light?
The wire colors are red and green/blue. Short the two pins of this plug with a short piece of wire or paper clip. Turn the key to the on position and the D4 will blink a code. One short blink = lock up clutch does not engage/disengage or unstable idle speed. Lockup control solenoid valve A Two short blinks = lockup clutch does not engage.
Is there a diagnostic code for fuel Moto?
Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
How do you check the Diagnostic Code on a Harley Davidson?
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9.
What does no RSP mean on a Harley Davidson?
“No Rsp” will also appear if the run/off switch is in the off position when doing this procedure. Also if the code set is a historic code (not a constant light) after 50 start and run cycles of at least 30 seconds each in duration, the light will extinguish itself as long as the error hasn’t occurred again.
Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
What are the diagnostic codes for a speedometer?
Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button.
How do you close the Diagnostic Code on a Harley Davidson?
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes.
On models not equipped with a tachometer “No Rsp” will appear when the tachometer identifier is selected. “No Rsp” (no response) will also appear if the run/off switch is in the off position when doing this procedure.