What does the clock spring on an airbag do?
The clock spring is simply a coil that retracts and expands inside its housing as the steering wheel turns. Its function is to maintain electrical continuity for all the components on the drivers airbag. The components include the airbag, horn, and any vehicle controls such as radio, cruise, heat and even telephone on some vehicles.
When do airbags need to be reprogrammed?
If the airbags did deploy, you will need to get brand new airbags, and the SRS airbag control module will need to be reprogrammed to remove all the crash data and hard codes from the accident. The impact sensors and clock spring may also need to be replaced if they suffered any damage or were melted during the accident.
What does the code on the air bag indicator mean?
If the system detects any problems, it gives you a signal through the airbag indicator by flashing the light several times, giving you the specific problem the test has detected. These flashes are codes, each having its own meaning. The supplemental restraint system (SRS) warning light is most commonly known as the airbag system light.
What does the my airbag reset code mean?
Typically, these codes will indicate that there is crash data stored, airbags deployed, communication failure, a full memory, or other airbag, seat belt related issues.
The clock spring is simply a coil that retracts and expands inside its housing as the steering wheel turns. Its function is to maintain electrical continuity for all the components on the drivers airbag. The components include the airbag, horn, and any vehicle controls such as radio, cruise, heat and even telephone on some vehicles.
Where is the air bag clockspring sensor module located?
An Air bag Clockspring is a part in your steering wheel that contains a spirally wound flat ribbon. Your AirBag Clock spring is an essential component of your car, truck or SUV’s air bag system. The part was a perfect fit, and $30 less than my local parts store.
If the system detects any problems, it gives you a signal through the airbag indicator by flashing the light several times, giving you the specific problem the test has detected. These flashes are codes, each having its own meaning. The supplemental restraint system (SRS) warning light is most commonly known as the airbag system light.
Are there two codes for air bag resistance?
There are two codes, B1 481 driver air bag resistance too … read more Have error code -1511 and the air bag light on. Replaced the Have error code B-1511 and the air bag light on. Replaced the seat belt assembly with new part, and the airbag light stayed on.
Why are the clock springs on my car not working?
Clock springs may become faulty with age due to electrical ribbons and their connections wearing thin. They also are likely to fail if they are not replaced after a car crash in which the airbag was deployed. Common signs you have faulty clock spring include:
When do you need to replace the clock spring?
The components include the airbag, horn, and any vehicle controls such as radio, cruise, heat and even telephone on some vehicles. The clock spring only needs to be replaced when the connectors that attach to the steering wheel airbag is melted and fused directly to the cylinder.
How does the airbag and steering wheel work?
The airbag and steering wheel electrical systems connect through a clock spring at one end and to the conductive ribbon at the other. Clock springs help operate the systems needed for turn signals, the horn, cruise control and more.
How does an airbag clock spring work in a car?
An airbag clock spring is used to connect the steering wheel to other electrical devices such as the airbag safety system, radio volume and station selections, horn and cruise controls. This is done using a series of small wires wound between an upper and lower plate which is mounted between the steering column and the steering wheel.
Can a clock spring be removed from a Hyundai?
Once you remove the steering wheel, you will be able to access the clock spring. Before you can remove the clock spring, you will need to remove the plastic trim, which is held in place with three screws.
Clock springs may become faulty with age due to electrical ribbons and their connections wearing thin. They also are likely to fail if they are not replaced after a car crash in which the airbag was deployed. Common signs you have faulty clock spring include:
Is it safe to drive with a bad clock spring?
A bad clock spring can also intermittently blow fuses as the car is driven. Is it Safe to Drive? Since the clock spring is responsible for two safety devices including the horn and airbag safety system it is highly advised to replace the clock spring with a new unit as soon as possible.
An Air bag Clockspring is a part in your steering wheel that contains a spirally wound flat ribbon. Your AirBag Clock spring is an essential component of your car, truck or SUV’s air bag system. The part was a perfect fit, and $30 less than my local parts store.
Why does the SRS light come on when you turn on the airbag?
When this happens, it’s common for it to short out or corrode, causing the SRS light to come on. The airbag clock spring sits inside your steering wheel and basically keeps the electrical wiring between the car and the driver-side airbag from being damaged as the wheel is turned.
Why does my airbag light come on when I turn the wheel?
The airbag clock spring sits inside your steering wheel and basically keeps the electrical wiring between the car and the driver-side airbag from being damaged as the wheel is turned. Over time, the airbag clock spring can become worn and damaged as a result of consistent turning of the wheel, which can trigger your airbag light.
Can You unplug the SRS airbag control module?
You are now safe to unplug the airbag control module harness wiring plugs. All airbag srs components must be installed and connected properly before installing the airbag control module. This includes air bags, seat belts, clock spring and impact sensors. Disconnect the battery and bolt down the module and then connect the harness wiring plugs.
How do you install an airbag control module?
All airbag srs components must be installed and connected properly before installing the airbag control module. This includes air bags, seat belts, clock spring and impact sensors. Disconnect the battery and bolt down the module and then connect the harness wiring plugs.