What are the injectors on a GMC diesel?
The fuel pressure regulator in the high pressure pump and the pressure regulating valve in the rail control rail pressure. The injectors have a piezo stack instead of an electro-magnetic solenoid.
How to check high pressure pump in GMC diesel?
Buy Fuel Pressure Regulator 2 Unplug the fuel pressure regulator 2 (pressure control valve in left hand rail) electrical connector. Crank the engine for 15 seconds and verify there is a steady flow of fuel from the fitting on the rail. If there is not, proceed to checking/replacing the high pressure pump.
How long does it take to replace fuel injection in GMC?
Crank or idle the engine for 15 seconds and measure the return quantity. If the quantity is greater than 3 ml in 15 seconds, replace it. Repeat for all eight injectors.
How to re-gas an out of gas fuel injector vehicle?
The steps are a little different, but the object remains identical: prime the pump and get fuel back into the engine. The first and only step that many people will need to take to restart a fuel-injected engine that has run out of gas is to simply add enough gasoline to the tank to submerge the pump (usually 1 to 2 gallons).
Why do fuel injectors need to be changed so often?
If an engine isn’t running efficiently, this can load extra pressure on injectors. It’s also important, to regularly change the fuel filter, to ensure a proper fuel flow. Driving Habits. Driving a car hard, combined with short start stop journeys, will increase the wear and tear on injectors.
How can I keep my fuel injector in good health?
Another great way to keep injectors in good health is; to regularly add a fuel injector cleaner to to your fuel tank. Many manufacturers claim that these cleaners, will give your car extra power or increased mpg. They probably won’t, or make much difference, to a car that is running properly.
Is there an error with my fuel injector?
An error occurred while retrieving sharing information. Please try again later. T-Shirts & DIY Gifts! Easy Speed Lesson!
Can a clogged fuel injector be repaired quickly?
Clogged injectors can usually be repaired, if you catch the problem quickly. Sometimes a fuel injector is completely clogged, because of years of neglect or a lack of regular engine servicing. If this is the case then a refurbished replacement, may be the only option.
Why is LB7 injector failure a common problem?
We know today LB7 injector failure is a common problem, and because the operating tolerances inside the fuel system are so tight, proper lubrication from the diesel fuel is critical.
Is the 2005 LLY injector Controle module new or used?
Must not been fixed at a GM Dealer? GM Part No.: 97303751 New OEM FICM about $1250 And used From $143 and everything inbetween. They should have some kind of guarintee. Is it new or used?
What to do if you have a bad fuel injector?
Possible bad injector, use the scan tool to cancel one cylinder at a time and see if the smoke clears up. However, using the scan tool to kill the injector does not reduce rail pressure in the injector and the tip can still leak fuel, cap off lines one at a time to pinpoint injector.
The fuel pressure regulator in the high pressure pump and the pressure regulating valve in the rail control rail pressure. The injectors have a piezo stack instead of an electro-magnetic solenoid.
We know today LB7 injector failure is a common problem, and because the operating tolerances inside the fuel system are so tight, proper lubrication from the diesel fuel is critical.
Are there any problems with the Duramax injectors?
However, Duramax injectors (in general) seem to be relatively sensitive to contamination and may fail prematurely if proper maintenance is not performed at regular intervals. It is extremely common for the injector wiring harness to chafe over time.
Possible bad injector, use the scan tool to cancel one cylinder at a time and see if the smoke clears up. However, using the scan tool to kill the injector does not reduce rail pressure in the injector and the tip can still leak fuel, cap off lines one at a time to pinpoint injector.