How do I reset my Cisco ASA 5505 to factory settings?

How do I reset my Cisco ASA 5505 to factory settings?

1. After you open connection, press enter a couple of times, and you should get a prompt like: ‘ciscoasa>’
2. type ‘enable’ to go to enable mode.
3. type ‘config t’
4. type ‘config factory-default’
5. hit spacebar when the ‘more’ is displayed.
6. type ‘reload save-config noconfirm’

How do I reset my ASA to factory settings?

Solution

1. Connect to the ASA via the console Cable.
2. log in and go to configure terminal mode.
3. Execute the following command “config factory-default”
4. Press the space bar a few times to execute the commands.

How do I reset my Cisco ASA 5505 password?

Reset Password in Cisco ASA Firewall

1. Step 1: Login to Cisco ASA device with console cable and reboot the device.
2. Step 2: Press ‘ESC’ key or ‘BREAK’ key on the keyboard to break the boot process.
3. Step 3: Now, here is the trick.
4. Step 4: Reboot the device.
5. Step 5: When the ASA is booted, it will not ask for password.

How do I connect to a Cisco ASA 5505?

Cisco ASA 5505 configuration

1. Step1: Configure the internal interface vlan.
2. Step 2: Configure the external interface vlan (connected to Internet)
3. Step 3: Assign Ethernet 0/0 to Vlan 2.
4. Step 4: Enable the rest interfaces with no shut.
5. Step 5: Configure PAT on the outside interface.
6. Step 6: Configure default route.

What is the default password for ASA 5505 in Packet Tracer?

This is written under the assumption that the ASA has been factory reset. Connect your console cable to the ASA and connect to it via Putty. Once the ASA has finished loading, go into enable mode. The default password is cisco with no username.

How do I restore my FTD to factory settings?

The command to reset a Cisco Firepower Threat Defense (FTD) appliance to factory defaults without completely re-imaging the device is configure manager delete. This will erase the entire configuration (firewall rules, data interfaces, routing etc).

How do I change my Cisco ASA 5505 username and password?

To set the enable password on your Cisco ASA 5505:

1. Get into the command line. I prefer using the console cable to directly connect.
2. Hit enter a few times to get the prompt.
3. Type ‘ena’ to enter enable mode.
4. Type ‘config t’ .
5. Type ‘enable password PaSsWoRd’ , replacing the second, ‘PaSsWoRd’ with desired password.

How do I configure an IP address on ASA 5505?

Set a Static IP for your Cisco ASA5505 Firewall

1. Open the ASDM and log into your device.
2. Under Configuration, Interfaces, select the Outside interface and hit Edit.
3. In the ‘IP Address’ box, click the radio for ‘Use Static IP’
4. Select an IP address, and use ‘255.255.
5. Hit ok, then apply.

Is Cisco ASA 5505 a router?

Note: If you purchase Cisco ASA 5505, please verify the package contents. The ASA is NOT a router, though and while you can do things on the ASA that can make it act something like a router it is important to understand the differences between true routing and what the ASA actually does.

How do I find my Cisco ASA encrypted password?

Normally, you use the ‘show run’ command to view the running configuration. Pre-shared keys are marked with an asterisk (*). To view the password unencrypted, type ‘more system:running-config’. This will display the full configuration with unencrypted passwords.

How do I reset my Cisco FTD?

How do I unregister from FTD FMC?

You do not need to unregister the other FMC.

1. Log into the Firepower Management Center.
2. Step 2 Choose System > Licenses > Smart Licenses.
3. Next to Smart License Status, click the stop sign ( ).
4. Step 4 Read the warning and confirm that you want to unregister.

Is Cisco phasing out Asa 5505?

there has not been any announcement for phasing out Cisco ASA 5505, it is not in the pipeline as of now. But if you want to work on the new ASA models, that should definitely help you and give you an edge in the longer run.

Can the ASA 5505 span a port?

Span/mirror port on the ASA 5505 – The ASA 5505 has an eight port Ethernet switch in it making it unique among the ASA product line. Like all Cisco switches, this one also supports traffic span to allow you to capture packets and send them to a destination switchport for analysis.

What is the Cisco ASA?

The ASA in Cisco ASA stands for Adaptive Security Appliance. In brief, Cisco ASA is a security device that combines firewall, antivirus , intrusion prevention , and virtual private network ( VPN ) capabilities.

What is an ASA router?

The ASA is a purpose built security device while the ISR is a router. The primary focus of the ASA is security implementation including stateful inspection of traffic and very sophisticated inspection of traffic passing through the ASA. It has some (limited) ability to do layer 3 routing of packets.