Is the throttle position sensor on a Honda CRV defective?
The throttle position sensor (TPS) on the 2002, 2003, and 2004 2.4L Honda CR-V is a simple 3 wire fuel system component that can be easily tested with just a multimeter (yup, no scan tool needed!). In this tutorial I will explain the TPS test that you need to perform to make sure that it is defective (or not).
How to test the TPS on a Honda CRV?
NOTE: You can find the 1997-2001 2.0L Honda CR-V TPS test here: How To Test The TPS (1997-2001 2.0L Honda CR-V). The throttle plate angle changes as you step on or off the accelerator pedal. And of course, it’s the throttle position sensor’s job to measure it and report it to your 2.4L Honda CR-V’s fuel injection computer.
How does the throttle plate change in a Honda CRV?
The throttle plate angle changes as you step on or off the accelerator pedal. And of course, it’s the throttle position sensor’s job to measure it and report it to your 2.4L Honda CR-V’s fuel injection computer. This throttle plate angle information is critical for your CR-V’s fuel injection computer.
How to test the throttle position sensor ( 1997 )?
Ground the black multimeter test lead directly on the battery negative (-) post. Manually rotate the throttle . You’ll get the best results by opening and closing the throttle directly on the throttle body instead of stepping on the accelerator pedal. The multimeter should show an increasing voltage as you (or your helper) open up the throttle.
The throttle position sensor (TPS) on the 2002, 2003, and 2004 2.4L Honda CR-V is a simple 3 wire fuel system component that can be easily tested with just a multimeter (yup, no scan tool needed!). In this tutorial I will explain the TPS test that you need to perform to make sure that it is defective (or not).
NOTE: You can find the 1997-2001 2.0L Honda CR-V TPS test here: How To Test The TPS (1997-2001 2.0L Honda CR-V). The throttle plate angle changes as you step on or off the accelerator pedal. And of course, it’s the throttle position sensor’s job to measure it and report it to your 2.4L Honda CR-V’s fuel injection computer.
The throttle plate angle changes as you step on or off the accelerator pedal. And of course, it’s the throttle position sensor’s job to measure it and report it to your 2.4L Honda CR-V’s fuel injection computer. This throttle plate angle information is critical for your CR-V’s fuel injection computer.
How to replace the TPS sensor on a Honda Civic?
Honda Civic: How to Replace and Calibrate TPS. 1 Step 1 – Remove the TPS. To remove the old TPS, first disconnect the throttle position sensor wiring harness. Remove the two 12mm bolts and nuts to 2 Step 2 – Install new TPS. 3 Step 3 – Calibrate the new TPS. 4 Featured Video: How to Calibrate TPS Sensor.
How can I Reset my throttle position sensor?
Reprogramming or resetting your sensor can sometimes solve these issues. This step can also be necessary when you install a new sensor. The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How to test the throttle position sensor ( TPS )?
For these two tests, go to: TEST 2: Checking Throttle Position Sensor (TPS) Power and Ground. CASE 3: The TP sensor signal’s voltage showed gaps in its voltage output as you tapped the sensor with the screwdriver.
When to replace the TPS sensor on a Honda CRV?
If the voltage signal (on your multimeter) reacted to the screwdriver tapping on the TP sensor, then this is a sure sign that the TPS is defective and needs to be replaced.
How does the TPS work on a Honda Civic?
Honda Civic: How to Replace and Calibrate TPS. The throttle position sensor, or TPS, is used to control the actual throttle position relative to the amount of feedback it receives from the “Go Pedal.”. If this sensor falls out of calibration or fails, you may experience issues controlling the throttle of the car.
For these two tests, go to: TEST 2: Checking Throttle Position Sensor (TPS) Power and Ground. CASE 3: The TP sensor signal’s voltage showed gaps in its voltage output as you tapped the sensor with the screwdriver.