Where is the reset SRS light on a Mercedes Benz?

Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car.

How to read and reset SRS / airbag light?

Battery dying. How to read and reset SRS/ Airbag light? Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it.

Why does my SRS light keep going on?

Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Step 1 Install a new battery; Step 2 Reset SRS/ Airbag light. Instruction on How to Reset the SRS Light on a Mercedes Benz: 1.

How to reset the SRS light on a Honda Accord?

(1) Locate MES Plug. It should be located near the driver’s side fuse panel under the dash. The harness is yellow with two wires. (2) Unplug the MES Plug. -Short and hold the leads while you turn the ignition to on. The SRS Light will illuminate for a few seconds then go off. -When the SRS Light goes off, unshort the wires.

How can I reset the SRS light or fix it?

There are two ways to reset the SRS light: with an SRS scanner and manually. The SRS Light can be reset with an OBD2 Scan Tool. When using an SRS scanner, there are a few steps to follow. Step #1 – Find the fuse-cover and take it off. Step #2 – Fit the scanner in the port. Step #3 – Turn ignition to the “run” spot.

Can the SRS light be reset at home?

You can reset the airbag light on your vehicle from your home garage, saving yourself a trip to the dealership or mechanic. The airbag light, also known as the SRS light (supplemental restraint system), illuminates on the vehicle’s instrument panel usually only after the vehicle has been in an accident and the airbag has deployed.

Why does the SRS light stay on?

If you see the SRS light on, you must work to know why. It can be due to a variety of reasons including: The malfunctioning of airbag sensors: It is common for the sensors to fail. This may cause the sensor to activate all of a sudden for no reason, causing the airbag light to stay on. Replacing the sensors may do the job.

Is it safe to drive with SRS light on?

While you can certainly drive while your SRS light is on, it isn’t safe. You should get your vehicle to a service center as soon as possible so that a technician can inspect your SRS computer.

Is there a SRS light on the dash?

On my W203 C class 2002 C230 Kompressor Coupe, Manual 6 speed, Audio 20 HU, CDC (added – read later, no other Audio or phone Fiber optics installed), with the basic HVAC control head. And a SRS light on the dash & MFD. Short Summary: Great experience. I scanned thru my OBDII port and found all errors.

Which is the best scanner to reset the SRS light?

Our favorite scanner that will read and reset your SRS / airbag light is the iCarsoft i980 for Mercedes-Benz which will retrieve the SRS light but also the check engine.

Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car.

Our favorite scanner that will read and reset your SRS / airbag light is the iCarsoft i980 for Mercedes-Benz which will retrieve the SRS light but also the check engine.

What does SRS warning light on Mercedes W204 mean?

Here’s what a solid SRS warning light could mean for your vehicle. This article applies to the Mercedes-Benz w204 (2007-2014). The supplemental restraint system (SRS) light in your vehicle will illuminate whenever there is a problem with your air bags or seat belt fasteners.

Where is the SRS scanner on a Mercedes Benz?

Plug in this scanner on the OBD II port found under the dashboard on the driver side. Hit Read on the scanner. Once the codes display on the LCD screen, hit erase. It’s that easy. Note that if the problem that caused the AirBag / SRS light to come on in the first place is not resolved, the Airbag / SRS light will come back on.

What does SRS stand for in Mercedes Benz?

In this video, we will show you how to use the iCarsoft i980 to reset the SRS on Mercedes-Benz cars manufactured after 1996. What does SRS light mean? SRS stands for Supplemental Restraint System.

When to reset service indicator light on GL450?

Service technicians reset the light during regular maintenance so it turns off until service is next required. You can manually reset the service indicator light when you maintain your vehicle. These instructions apply to the 2011 GL450. The sequence is the same or similar for previous model years.

In this video, we will show you how to use the iCarsoft i980 to reset the SRS on Mercedes-Benz cars manufactured after 1996. What does SRS light mean? SRS stands for Supplemental Restraint System.

When to reset the service indicator light on a Mercedes?

The Mercedes Benz GL450 sport-utility vehicle is equipped with a service indicator warning that is displayed at regular mileage intervals when maintenance is needed. Service technicians reset the light during regular maintenance so it turns off until service is next required.

How to reset Mercedes-Benz C Class W204 service indicator?

Press the down arrow until you are highlighted on “Full Service”, then press “OK”. Press the down arrow until you are highlighted on “Conf. Full Service”, then press “OK”. Press the down arrow until you are highlighted on “Yes”, then press “OK”. Press the down arrow until you are highlighted on “Confirm”, then press “OK”. Loading…

Where can I get a Mercedes Benz serviced?

When it comes to servicing your Mercedes-Benz, trust the experts at the Mercedes-Benz of Denver Service Department. Let our certified Mercedes-Benz technicians perform the required scheduled maintenance on your new and certified pre-owned Mercedes-Benz vehicle. Don’t know whether you need a Service A or B? Let us help!

What does it mean when SRS warning light stays on?

SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system. It is very unlikely that your airbags are going to deploy randomly, but the concern is that they may not deploy…

Where is the SRS light on the dash?

If the red SRS lamp on the dash is accompanied by the orange airbag lamp next to the transmission shifter is lit, the fault is commonly connected to the passenger seat sensor.

Why does the SRS light keep coming on and off?

If the SRS light stays on or starts flashing on and off, you may have a problem with the airbags themselves, a loose wire, a faulty seat belt buckle, or a problem with the Engine Control Unit (ECU) that is causing the airbag warning light to stay on.

What does the ABS warning light on a Mercedes mean?

If the ABS warning light is also illuminated this signals that the braking system has malfunctioned and your brakes may not work properly. In this case the Electronic Brake Force Distribution (EBD) warning light may also be illuminated. Can I still drive with my parking brake and brake fluid light on?

What to do when your abs warning light goes off?

Once you have determined you are going to fix the problem, park the car on level ground with the transmission in park and the emergency brake set with the engine turned off. You may need to jack the car up to remove a tire or replace a control module. Always stay safe by using jack stands when lifting a car for repairs.

How to fix no power no start on most Mercedes-Benz?

HOW TO FIX NO POWER NO START ON MOST MERCEDES-BENZ VECHICLES DIY. – YouTube HOW TO FIX NO POWER NO START ON MOST MERCEDES-BENZ VECHICLES DIY. If playback doesn’t begin shortly, try restarting your device.

Why is my Mercedes Benz starter not working?

Often times, when the starter is defective or seizes up it will blow out the fuse that protect the starter circuit. Another thing that you can try is to hit the starter with a rubber hammer a couple of times. Depending what kind of starter problems you have, the starter may work a few more times.

Is there a scanner that reads the SRS light?

Here is a scanner that works with Mercedes-Benz and will rear fault codes and reset the AirBag, ABS and check engine light. Our favorite scanner that for an in-depth Mercedes-Benz troubleshooting is the iCarsoft MB II. Not only does it read the SRS light (Airbag Control Unit) but also every control unit in your Mercedes-Benz.

What happens when you replace the battery on a Mercedes?

Upon replacing, the dash warning lights for “BAS ESP and ABS” are still lit and will not go out. Is there something that I can do to reset, or do I have to take to dealer. Also, left window now will not go back up + I cannot pop hard top. Please help. I don’t want to get ripped off by the dealer over replacing a battery.

Why does my Mercedes ASR light keep coming on?

Step 1: Ensure that the main battery on your Mercedes-Benz is holding a proper charge. Mercedes-Benz cars are very sensitive to low voltage. An old battery can be the primary cause of BAS/ASR lights staying on. It is common for BAS / ASR lights to come on with a dead battery. It takes a while for a discharged battery to charge fully.

What should I do if my battery goes out on my 1999 SL500?

I have a 1999 Sl500. I just replaced the battery today. Upon replacing, the dash warning lights for “BAS ESP and ABS” are still lit and will not go out. Is there something that I can do to reset, or do I have to take to dealer.

Where is the SRS fault on the Mercedes E class?

Here is a way to deal with a common SRS fault that lies within the seat pad of the Mercedes E Class (W210). (I am sure also similar for other models)

When does brake warning light go off on 2003 C320 mecedes?

High School or GED 19,538 satisfied customers a170 auto: A170 (2003 model ) auto . when starthing and having A170 (2003 model ) auto . when starthing and having foot on brake pedal all warning ligths og off . 3 sec afther removing foot from brake the abs and esp light goes on and remains on until egnition is…

How to reset the Mercedes Benz ESP warning light?

Replacing the ABS sensor is easy, you can learn how to replace ABS sensor here. Note that once you will replace the ABS sensor and will still have the ESP warning light on. You will need to follow the procedures below to reset the light.

Where is the steering angle sensor on a Mercedes Benz?

Steering Angle Sensor – is right behind the steering wheel in the steering column. It’s the main purpose is to calculate the angle of the steering wheel so that the car knows if you are taking a turn or if you are going straight. The input from the steering angle sensor is used by the ESP control module.

How do you reset the TPMS light on a Mercedes Benz?

Find the service button on your screen, you might have to scroll down. Once you click on the ‘service’ button, find ‘tire pressure’ and select it. This will actually display what your tire pressures are. Once you adjust to the correct pressure, you can reset the TPMS light.

How do you reset the SRS light on a Honda CRV?

Put the key in the ignition and turn it on, but don’t start the engine. Keep the ends of the wire touching while you do this. The SRS light will flash on, and then disappear. Separate the wires immediately. The SRS light should come on again. Repeat Step 3 and the SRS light will blink twice and turn off.

Are there any problems with the Mercedes CL500?

Keep track that the ABC fluid is good is another important issue with any ABC equipped Benz. These cars are heavy. Your going to burn through front pads and tires every 20,000. But my CL is a pleasure and has been very dependable car overall. My 2000 CL500 just hit 88]

What should I do if my SRS light comes on?

If you need a scanner that will also troubleshoot Transmission, ESP, ABS and any other control unit on your Mercedes-Benz, check out the iCarsoft MB II, a powerful diagnostic scanner for Mercedes-Benz cars. Want to know why the SRS light came on?

What does the SRS light mean on a Mercedes Benz?

What does SRS light mean? SRS stands for Supplemental Restraint System. If this warning light stays on in your Mercedes Benz, that means that there is a problem with the airbags or the components that are part of the SRS system.

Is there a recall on the CL500 air pump?

You can thank the EPA for that one… it dosen’t actually purify anything, rather just tricks the computer to “think” it is burning cleaner… anyhow, there is a recall for the relays that operate the air pump, and they stick open causing the pump to stay running and burn out. The $40 relay burns up a $400 pump.

How to remove the SRS light from your car?

Quick Fix to remove SRS Dash light. Lightly jiggle a small flat head screwdriver into the seatbelt connectors, then spray electronic connector cleaner (radio… Quick Fix to remove SRS Dash light. Lightly jiggle a small flat head screwdriver into the seatbelt connectors, then spray electronic connector cleaner (radio… Skip navigation Sign in

Where are the fuses located on a cls500?

Fuses and Relays in the engine comparment. Here you will find fuses 43 to 67. The unit where the fuses are installed is also called the driver side SAM control unit (N10/1) which has fuses and relays. SRS Restraint system. Tension retractor In the fuse box located on the side of the dash, driver side, you will find fuses 21 to 42.

Why is my SRS light on in my Mercedes C class?

A malfunctioning seat belt could cause the SRS light in your Mercedes-Benz C-Class to display on the dashboard. The same is true even if the air bags in your vehicle are safe to deploy in a crash. If your C-Class is under warranty, the dealer will replace the malfunctioning seat belt (s) at no cost to you.

Is there a way to reset the SRS light?

You can’t rest the airbag SRS light with a simple OBD II scanner which gives you the check engine light codes. You will need a more advanced scan tool to reset the airbag light. For around $110-150, which is how much a diagnosis costs anyway, you can get your airbag reset tool.

How to reset service light indicator Mercedes E320?

How do you reset service indicator light Mercedes E320. From years: 1997, 1998, 1999, 2000. Diagnostic Reset Tool Required (please refer to TOOLS page) Manual Reset. Turn key in steering lock to position 2. Within 4 seconds press 0 button twice.

How to reset SRS / airbag light on Mercedes Benz?

Find the port that fits the OBD cable and plug the scan tool’s cable into this port. 2. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts. Look at your OBD scan tool and write down the codes it displays. 3. Check your owner’s manual for what the codes mean. 4.

Where is the SRS light on a Mercedes Benz?

This is located on the lower left side of the control panel on the driver’s side of the car. Find the port that fits the OBD cable and plug the scan tool’s cable into this port. 2. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts.

Why did my Mercedes SRS air bag go off?

Understanding that the weight may fool the occupancy sensor to thinking an adult bum is on the seat, the child seat detector overrides this and signals the Air Bag Control Module to turn off passenger side airbags. When it does this, the orange Air-Bag off transmission LED illuminates showing the system is disabled and its safe for baby to travel.

Where is the contact matrix on a Mercedes SRS?

Layered within the seat base skin of the passenger seat, there is a complex contact matrix (like a foil printed circuit – looks like an aerial view of a maze) that senses if the seat is occupied (a bum on it) and in most cases with post face-lift models, also auto-senses the proximity of the MB child seat.

Is the front passenger airbag disabled in Mercedes?

Mercedes Front Passenger Airbag Disabled Enabled See Oper. Manual Mercedes-Benz vehicles including E, C, S, CLS, ML, GL, R, G Class, may display a warning message stating front right SRS has malfunctioned and needs to be repaired. Front Passenger Airbag Disabled See Oper.

Why does my Bas light come on in my Mercedes Benz?

To reset the lights, start up your Mercedes-Benz and turn the steering wheel all the way to the right, then all the way to the left. Do this a couple of times. Turn off the engine. Restart. Brake Light Switch may cause BAS / ESP / ABS light to come on. It is the most common problem with Mercedes-Benz cars.

Is the Check Engine light on in my Mercedes?

Has the check engine light turned on in your Mercedes-Benz C-Class, E-Class, GLA, GLC, GLE, ML, or SL? It can be alarming seeing an engine warning appear on your dashboard, especially if you’ve never seen it before.

When does the Check Engine light come on on a Mercedes?

It illuminates when something requires the attention of a mechanic, or to remind you of periodic service needs. The light is designed to come on when the vehicle passes certain mileage limits. You can reset the “check engine” light on your Mercedes within a few minutes.

How to reset the SRS warning light by yourself?

Step 8: You should hear beeps for 3 seconds, and when the beep is gone, the SRS should turn OFF. Step 9: QUICKLY, Take the paperclip/wires out and the light should come back on. Step 10: When the light comes on, QUICKLY plug the paperclip back in to complete the curcuit again, in a second or so, the SRS light should TURN off

Why does the SRS / airbag light stay on?

When do you need to replace the SRS sensor?

Its very rare for a sensor in the front to go bad but if you have been in to an accident and your airbag didn’t deploy but the seatbelt locked, YOU MUST replace the SRS module.

Where is the fuse for the SRS light?

In most models, this is fuse #40, located in the lower right corner of the fuse block. Turn the ignition switch to “ON” without starting the engine. Leave the ignition on for about one minute to allow the system a chance to reset. Turn the ignition off.

What do the lights on the Mercedes dashboard mean?

Modern Mercedes-Benz cars are filled with lots of sensors that monitor how each system in the car is behaving. The lights on the dashboard display what systems are in use and they also highlight when one of those systems is not working as it should. But what do all those different symbols mean?

What are the fault codes for Mercedes SRS?

Child seat:”Signal” transmission fault between front passenger seat and “Babysafe” Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. C1011. BAS light, play in steering column causes steering angle sensor to lose memory (?) C1401.

When does the SRS light come on in a car?

The SRS (airbag) light can come on if liquids are spilled into the seat belt buckles, or if the liquid pools underneath the seat and gets into the electrical connector for the seat belt pretensioner. Damaged components will require replacement to restore proper airbag operation.

What should I do if my SRS warning light stays on?

If you are that lucky, you should consider getting the Autel DS708 which covers more vehicles, not just Mercedes-Benz. It allows you to read and diagnose control systems in most cars. You can perform programming and stream sensor data live.

Which is the best scanner for Mercedes Benz?

(DS708 is will be a better choice if money is not an issue for you and you have many cars, for DS708 covers more vehicle and can read codes or diagnose on more systems in the car.) My experiences: A copy (thanks gurunutkins) of CarSoft V7.4S scanner.

Why does my SRS light not turn off?

Tried turning the steering wheel left to lock and right to lock 5 times, SRS will not turn off. Drove the car for about 30 minutes, still would not turn off. But, in the dash display for mileage, there is no reading that I have an SRS problem and/or SOS take it to the workshop?

How long does the SRS warning light stay on?

While your car will run with this light on, it is important that you diagnose this problem as soon as possible. Under normal operations, when you first turn the ignition and start the car the light stays on for about 5 seconds and then turns off.

Why does the SRS light come on on my Mercedes?

We Can Fix It! In the majority of cases when the SRS light is on on your Mercedes, the fault is associated to the passenger seat pad. In the passenger seat there is an electronic pad that sensors whether the seat is occupied and therefore switches the passenger air bag on or off.

What does the SRS light on the dash mean?

The supplemental restraint system (SRS) light in your vehicle will illuminate whenever there is a problem with your air bags or seat belt fasteners. Look for a solid warning light on your dash to identify signs that one or both parts could be malfunctioning, or in need of repair.

What should I do if my Mercedes SRS breaks?

So the first thing to check is the connector and it wires (best to remove the seat) If the break is suspected within the depths of the seat base, then it has to be stripped to repair/replace the parts. (This is where the repeat £220 bill from the agents came from!)

Here is a way to deal with a common SRS fault that lies within the seat pad of the Mercedes E Class (W210). (I am sure also similar for other models)

What do you need to know about SRS system?

Airbags contain perchlorate material which required special handling. Air bags and Emergency Tensioning Devices (ETD) are designed to function one time only. Once these systems deploy they must NOT be reused. If you work on the SRS system, you should disconnect the battery. Do not use seat covers unless approved by Mercedes-Benz.

How can I Turn Off the SRS light?

This was a mistake because you cannot disconnect the wire harness from the column to the airbag to check for faulty wiring. You can unplug the wire from the airbag, by carefully pulling the plug. You need an allen wrench to remove the two screws on the back of the steering wheel to remove the front cover.

How much does it cost to repair a SRS light?

He said it was just the wiring harness that attaches to the sensor that costs about $20 to repair. But with labor, parts and reset it costed me almost $200. With Transmission flush (almost $500), free car wash, and SRS job, with a 15% off coupon, I paid about $670. Not bad.

How often does Mercedes W210 SRS need to be serviced?

The service history of my current E Class W210 shows repeat visits over 10 years for this specific SRS problem and I would like to share with you the ins and outs of it all (each visit cost the previous owner £220 for the cure/pleasure – only to have it return again almost every 18 months to 2 years during ownership)

What does the SRS light on a car mean?

When you see the Supplemental Restraint Systems (SRS) light illuminated on the control panel of your Vehicles it means there is a problem with the airbags or the seatbelt tensioners. When there is a malfunction in the Vehicles codes are stored in the On-Board Diagnostics (OBD) computer.

Is there a way to read the SRS light?

Not only does it read the SRS light (Airbag Control Unit) but also every control unit in your Mercedes-Benz. Note that this does not work with Mercedes-Benz, pre-2000 that require 38-pin connection. For those models you should consider the Carsoft Multiplexer 7.4 which requires a laptop. Unless you are not concerned about the cost.

Are there any common problems with Mercedes SLK?

i think its more related to the “type ” of slk he is looking at. for instance some common issues for slk may be. top issues ie: hydraulic cylinders leaking seals cracking hinges stiff. brakes and services performed. slk32 issues are intercooler pump, lower a arm bushings.

Where is the yellow connector on a Mercedes SRS?

There is a yellow connector beneath the seat, this houses all the connections to the seat pad sensor and links its signals to the ABCM.

How to change the fluid in a SLK?

Look in the w210 forum for 722.6 sticky, how to change the fluid – look at post by Yumling for optimal fluid change, quantity and type of fluid, etc. Type of fluid especially important! You also have to buy or make a dipstick. It does not stay in place, but is only used to measure the level.

Can a faulty seat sensor cause an airbag light to come on?

Before you decide to bypass the passenger seat sensor, use an airbag scanner to verify that the airbag light is due to the seat weight sensor. If yes, call your dealer to check if there is a recall on these problems. Most car manufacturers will replace the passenger seat sensor free of charge even if they are out of warranty.

How to replace the SRS seat pad light?

1. At some point, have the codes read, by an inde, (PIC 1 ) as having the seat pad SRS light on will ‘MASK’ other ( emergency tensioning retractor belt and bag) faults. 2. Buy a NEW sensor first, (PIC 2 ) I have not seen ANY signs of wear ( wires, scraping, breaks ) at all. The sensor ‘dots’ fail with use/age. Sensors cost 140 US$ at MB. 3.

Do you need to disconnect seat covers for SRS?

Air bags and Emergency Tensioning Devices (ETD) are designed to function one time only. Once these systems deploy they must NOT be reused. If you work on the SRS system, you should disconnect the battery. Do not use seat covers unless approved by Mercedes-Benz. Seat covers can restrict the proper operation of the airbags integrated into the seats.

How to reset adaptive shifting points on Mercedes Benz?

This procedure will reset the adaptive shifting points in your Mercedes-Benz automatic Transmission Control Unit (TCU). These simple do it yourself instructions take less than 5 minutes. No tools are required to perform this procedure and make your Mercedes-Benz shift like new. Try this if your car has been shifting sluggish recently.

What causes a Mercedes SRS to lose memory?

Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. C1011. BAS light, play in steering column causes steering angle sensor to lose memory (?) C1401. BAS light, play in steering column causes steering angle sensor to lose memory (?) Driveline Disconn.

When to replace battery in Mercedes SL Class R129?

Replace your battery if it is 5 to 7 years old. A slipping drive belt will squeal and a broken one will leave you stranded. Check your drive belt. A broken drive belt tensioner is just as bad a a broken accessory drive belt. Is your car running a little hot in traffic?

How to reset a Mercedes Benz after a flat battery?

How to Reset a Mercedes-Benz After a Flat Battery. 1 Step 1. Insert the reset tool into the Mercedes’ data-link connector, which is near the hood-release latch. Turn on the ignition. 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5.

How do I reset the soft top on my Mercedes SL?

This is usually accomplished by having the cargo cover in place and closed. If it is open – the computer thinks the trunk doesn’t have room for the top so it will not operate. Your model of SL does not have the retractable top, but probably still has a similar type system.

Why is my Mercedes-Benz SL Class not working?

If it is open – the computer thinks the trunk doesn’t have room for the top so it will not operate. Your model of SL does not have the retractable top, but probably still has a similar type system. Try this link – http://mbworld.org/forums/sl-class-r129-18/ this should be a good starting point to finally get the problem resolved

Why does my Mercedes-Benz C220 speedometer not work?

What are common reasons my Mercedes-Benz C220 has a speedometer that doesn’t work? While there are a variety of reasons your Mercedes-Benz C220 speedometer is not working, the most common 3 are the vehicle speed sensor (VSS), a faulty speedometer, or an electrical issue.

Where is the SRS warning light on the dash?

1. SRS warning light on dash coming on intermittently or permanently 2. SRS warning light on console, between front seats, illuminated intermittently or permanently. As mentioned elsewhere in this Forum the light can illuminate when the SRS seat pad sensor connector under the passenger seat is suspect.

What causes a Mercedes SRS to go out?

The cause is the cable routing under the passenger seat. The wire was dressed from the factory such that the cabling to the connector was under tension. The cause is the cable routing under the passenger seat. The wire was dressed from the factory such that the cabling to the connector was under tension.

How do you reset SRS on a Mercedes Benz?

Turning the steering wheel fully left and right doesn’t reset SRS – it re calibrates the steering angle sensor. If you disconnect the vehicle battery, you will need to do this if the ESP error light is illuminated. Start the engine and then run the steering through its full left and right range. That will extinguish the ESP light.

Where is the SRS light after the fuse reset?

SRS Light After Fuse Reset! Fuse Box: 1 inside the car, next to the Driver’s door. The other day i was checking my fuses to see which one went bad when i put in my radio. I removed one by one until i found the bad one. But now my SRS light came on and will not go off. I guess removing the fuse and put it back has brake the circuit with the battery.

Navigation