How do you change the brake pads on a Honda Civic?
How to Change the Brake Pads on a 2003 Honda Civic. Remove the tire, and put it to the side. Use the 12-mm socket and the ratchet to remove the two bolts on the back of the caliper that hold it place. Pull the caliper off the rotor, and let it rest on top of the rotor. Do not let it hang from the brake line. Spray the rotors with the brake cleaner.
How do you replace a tire on a Honda Civic?
Place the caliper back over the caliper bracket, and secure it into place with the two 12-mm bolts on the back of the caliper. Replace the tire, and tighten the lug nuts. Move to the other side of the vehicle, and perform the steps to replace the brake pads on that side. Raise the Civic up off of the jack stands and remove them.
How do you remove a brake caliper from a car?
Pull the caliper off the rotor, and let it rest on top of the rotor. Do not let it hang from the brake line. Spray the rotors with the brake cleaner. Remove the old brake pads from the caliper bracket that is still on the rotor with a slotted screwdriver.
How do you replace brake pads on a car?
Remove the C-clamp and the old brake pad. Place the new brake pads in the caliper bracket where the old brake pads used to be. Place the caliper back over the caliper bracket, and secure it into place with the two 12-mm bolts on the back of the caliper. Replace the tire, and tighten the lug nuts.
How do you change brake pads on a Honda Civic?
Apply anti-squeal paste to the surface between the caliper and brake pads. The caliper piston needs to be pushed back as the new pads are thicker and the pistons are likely pushed out from the old worn out pads. Open the brake fluid reservoir to allow pressure to be relieved.
How do you replace rotors on a Honda Civic?
Lay the rotor on the hub and tighten the mounting screws. Place the new caliper bracket on and install the brake pads. Before installing the pads, apply brake lube on top of them. Figure 8. Install new rotor. Figure 9.
How do you replace the caliper on a Honda Civic?
Flip the caliper over and use a clamp to compress its piston. If the piston fails to move, the caliper is seized. Check the brake pads and rotor to see if they adhere to at least their respective minimum thickness. If they do not, replace them. Figure 3. Remove the lower caliper bolt. Figure 4. Compress the caliper piston. Figure 5.
Where is the brake line on a Honda Civic?
Locate the brake line that extends from the brake caliper. It is attached to the wheel bearing housing by two 10mm bolts; remove to free up the line for more room to move around later. Remove two 17mm bolts holding the brake caliper bracket.
How do you replace disc brakes on a car?
On some rear disc brakes, the caliper pistons screw in, and require the disc brake pad spreader set to be seated properly. Take the caliper off the bungee cord and put it back on. VERY IMPORTANT – DO NOT OVERTIGHTEN the caliper bolts.
How to replace brake pads and rotors step by step?
Check out the video above or keep scrolling for general steps on how to replace brake pads and rotors in the most vehicles. Park the vehicle on a dry, flat surface and install wheel chocks. Be sure to wear safety goggles and protective gloves. Be careful when lifting the car. Use secure jack points for the jack and jack stands.
Loosen the wheel lug nuts by turning them 45 degrees counterclockwise. Jack up the front of the vehicle. To do this, put the floor jack under the vehicle and jack up on the front jack point of the Civic (located near the radiator–it’s an extension of the frame).
How do you jack up a Honda Civic?
Step 1 – Jack up the car. Park the car on a level surface. Place a pair of wheel chocks behind the rear wheels to prevent the car from rolling backwards. Look for the front jack point, and place your jack underneath it. While there are other suitable places you can use, this is by far the best and strongest jack point.
Where to put the Jack on a Honda Accord?
Place a pair of wheel chocks behind the rear wheels to prevent the car from rolling backwards. Look for the front jack point, and place your jack underneath it. While there are other suitable places you can use, this is by far the best and strongest jack point. The factory jack shows four other jack points,…
On some rear disc brakes, the caliper pistons screw in, and require the disc brake pad spreader set to be seated properly. Take the caliper off the bungee cord and put it back on. VERY IMPORTANT – DO NOT OVERTIGHTEN the caliper bolts.
Clean the wheel hub with brake wash. Apply brake grease to the locations on the wheel hub where the brake shoes make contact. Slide the new brake pads into position on the wheel hub. Reassemble the brake by reversing the process that you used to disassemble it. Repeat this procedure on the wheel on the other side of the car.
How much does it cost to replace a disc on a Honda Civic?
Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. received a Brake Rotor/Disc Replacement. Honda Civic Brake Rotors/Discs Replacement costs $336 on average. What is the Brake Rotor/Disc all about? A brake rotor is a smooth metal disc attached to the wheel hub.
What kind of brakes does a Honda Civic have?
One of the most vital systems on your Civic is its brakes. Failure to maintain the brakes on your Civic can greatly impact your safety as well as others on the road. Like many cars, the brakes used on the Civic’s rear wheels are drum brakes.