Where is the fuel pump relay in a GMC Sierra 1500?

The control module under the truck box took the place of the fuel pump relay or fuel pump regulator. It is a 5″×5″ flat box about 1/2 in. Thick bolted up under the box. Remove spare tire to get to it. 9 people found this helpful. Remember: There is nothing in the fuse box marked [Fuel Pump] location.

Why does my car have a fuel pump shut off switch?

Many vehicles come with a fuel pump shut off switches. The inertia switch is a security measure implemented by car manufacturers in order to shut off the fuel supply in case of a car crash or some accident where a vehicle comes to a sudden stop instantly.

Where is the fuse for the fuel pump?

Were is the fuse and relay located if not in the box 23 people found this helpful. The fuel pump relay has no relay. Only a yellow 20 amp fuse for the pump. It may be marked under the plastic cover but not present. The control module under the truck box took the place of the fuel pump relay or fuel pump regulator.

Where is the emergency fuel shut off switch?

Emergency Fuel Shut Off Switch Location on Other Cars On Ford, Peugeot, VW, Citroen, Vauxhall, Subaru, Renault, Toyota and Mazda, inertia switch location is usually on one of the following two hidden places: Behind or below glove compartment, sometimes hidden under the carpet; Under side-panel located next to the drivers’ door;

What to do if your fuel pump wont start?

For future reference, I had this same problem when replacing the fuel pump on my 2002 s10 4.3L. Searched forever for an answer. It turns out that in order to remove the bed of the truck, you must disconnect the ground for the fuel pump, which attaches in the rear on the drivers side.

Why does my son’s GMC Sonoma not start?

I have a huge favor and I’m stuck my son has a 2003 gmc Sonoma pulled into our driveway went to start it back up it would not start checked everything and it seem to be the fuel pump so we purchased a new fuel pump and we still can’t get it to start we have replaced the control module and it still won’t start any buddy have any ideas

How does a fuel pump relay get power?

The relay wires should have ground on two wires, power on one wire and switched power on another wire. To activate the fuel pump the computer actually connects one of the ground wires to complete the circuit and send power to the fuel pump.

Where does the fuel pump go in a truck?

Searched forever for an answer. It turns out that in order to remove the bed of the truck, you must disconnect the ground for the fuel pump, which attaches in the rear on the drivers side. IIRC it ran either in or alongside the harness for the tail light wiring. Once I hooked that back up, my truck started right up.

Why does my GMC Sierra suddenly stop running?

Truck suddenly stops running, acting like it’s out of fuel. There is fuel in the gas tank and, I can hear the fuel pump when I turn the ignition on. Is there a fuse, or relay that is maybe causing this to happen?

When is the fuel pump relay turned on?

The fuel pump relay is activated whenever the ignition is turned on. A fuel pump relay functions primarily to maintain a consistent voltage supply to the fuel pump. The ignition or powertrain control module (PCM) usually controls the fuel pump relay.

How does a GMC Sierra 1500 fuel pump work?

The older model has steel lines coming off of the top of the pump to the frame rail and then connects to the frame steel lines with short hoses, you’ll need line wrenches and the ability to curse. The newer style has plastic tubes from the plastic pump casing and uses those quick connect fuel fittings and you’ll need the disconnect tool.

Is there a fuse and relay on a GMC Truck?

My friend has a 07.5 chevy with a fuse and relay but in my 09 it doesn’t. My truck kept dying on me and throwing codes. Ended up being the module above the spare tire not being sealed correctly from gm. Definitely was confused tho when I didn’t see a relay or fuse…

Is there a relay for the fuel pump?

I’m guessing there is a relay because every fuse that has to do with the fuel pump is missing. Not even a dealership could help me with an answer. Im just being curious and figured The wonderful GMFS could help me out. You tell me? I’m guessing there is a relay because every fuse that has to do with the fuel pump is missing.

Is the fuel pump relay controlled by the PCM?

Consequently, the fuel pump relay is usually controlled by, the ignition or powertrain control module (PCM). As a result, when switched on, the fuel pump relay; will provide current to the fuel pump, so that it may function. Therefore, any faults with it, can cause fuel pump issues.

What happens when the fuel pump relay fails?

When the ignition is in the “ON” or “START” positions, the PCM energizes the fuel pump relay in order to turn on the fuel pump. When this relay begins to fail, the fuel pump will operate intermittently or completely fail to operate, resulting in the engine stalling or the inability to start the engine.

How to test a GM 4.3L fuel pump?

More GM 4.3L, 5.0L, and 5.7L Tutorials. It’s very important that you start off your fuel pump relay diagnostic by first testing the fuel pump pressure with a fuel pressure test gauge. If the fuel pump relay IS NOT activating the fuel pump, the fuel pressure test gauge will register 0 PSI when cranking the engine.

Were is the fuse and relay located if not in the box 22 people found this helpful. The fuel pump relay has no relay. Only a yellow 20 amp fuse for the pump. It may be marked under the plastic cover but not present. The control module under the truck box took the place of the fuel pump relay or fuel pump regulator.

Why is the fuel pump relay not turning on?

The ECM controls the fuel pump relay and this relay will only energize when commanded on. Does the check engine light come on; if not, then the ECM is not turning on. Do all the other combination meter warning lights come on?

How do you test a fuel pump relay?

Ignition OFF, disconnect the harness connector at the FPCM. Ignition OFF, install a test lamp between the control circuit terminal 13 and ground. Ignition ON, verify that a test lamp illuminates for 2 seconds.

How to install a new fuel pump relay?

1 Install relay. Install the relay into the fuse box the same way the old relay was removed. 2 Put on the fuse box cover. Snap it into place. Note: If you had to remove screws or bolts from the cover, be sure to install them. 3 Remove the fuel cap from the fuel tank. Put the fuel cap back on and make sure that it makes a good seal.

Why is my fuel pump relay outside the fuse box?

If it’s located inside the engine bay, which can get hot from the engine’s heat, the heat can impede the relay’s performance. In addition, in the rare cases where you will find the relay placed in the engine bay but outside the fuse box, it will be exposed to heat plus dust and dirt.

Is the fuel pump on my Silverado working?

Worked great on my 2009 Silverado. The seals on these must be going about the same time as there are a lot of posts recently appearing about this part failing. Mine had been collecting water for a while as seen from rust stains inside the old one.

Can a GMC Sierra run without a fuel pump?

Without gas your Sierra will not run at all. With that in mind, most of the symptoms of a bad fuel pump revolve around the vehicle stalling out or not running at all. In modern fuel injected vehicles, the fuel pump sits right in the fuel tank and “pushes” the gasoline to the fuel rail (s).

Where is the relay on a GMC 6.2?

Those “gem” threads answered it perfectly. Relay is above the spare tire. My 6.2 is strong and sexy, but it still needs help sucking it’s own gass. Lol It’s crazy how GM can make (what seems to me) pretty major mods by adding relays here and deleting fuses there, but forgetting to update the manual and fuse box diagram.

What are the fuses on a GMC Sierra?

RH Turn and Stop Lamp) ECM 1 Fuse #15 10A Vehicle Control Module (VCM)/Powertrain Control Module (PCM) from IGN I Relay) INJA Fuse @20 15A Fuel injectors 1. 3, 5, and 7. Ignition Coils. Glow Pug Module, Fuel Heat. Water in Fuel (WIF) Sensor, Wastegate Solenoid IGN E Fuse #25 10A NC Compressor Clutch Relay.

Where can I test my fuel pump relay?

Where To Buy The Fuel Pump Relay. TEST 1: Swapping Out The Fuel Pump Relay. TEST 2: Making Sure The Fuel Pump Relay Has Power. TEST 3: Bypassing The Fuel Pump Relay. TEST 4: Bench Testing The Fuel Pump Relay.

What kind of Fuse does a GMC Sierra use?

LBEC 2 50A LOCKS Fuse. DDM Fuse, PDM Fuse, ECC Fuse, AUX PWR 2 Fuse IGN A 40A Ignition Switch RUN. START. RUN/START/ACCY

Where is the oil pressure switch on a GMC Sierra 1500?

Because you have a ECM electronic control module. You only have a yellow 20 Amp fuse in the upper far right corner of the fuse box panel under the hood. Extra tip: replace your oil pressure switch. It way in the back of the motor. You need a 27mm deep well socket, 3/8 drive and a stubby flex ratchet, small hands help too.

Where can I buy a fuel pump relay?

At O’Reilly Auto Parts, we offer high-quality fuel pump relays. Check out our stock of fuel pump relays to find the part you need for your repair.

What to do if your fuel pump relay is overheating?

Pull out the relay and visually inspect the terminals and socket; for signs of corrosion and overheating. Consequently, Corrosion prevents proper current flow; and overheating indicates problems with the relay or circuits it connects to. Clean corroded terminals and socket with electrical contact cleaner. Next Check all fuses before any repairs.

LBEC 2 50A LOCKS Fuse. DDM Fuse, PDM Fuse, ECC Fuse, AUX PWR 2 Fuse IGN A 40A Ignition Switch RUN. START. RUN/START/ACCY

How much does a GMC Sierra fuel pump cost?

Your GMC Sierra 1500 will be happy to know that the search for the right Fuel Pump products you’ve been looking for is over! Advance Auto Parts has 103 different Fuel Pump for your vehicle, ready for shipping or in-store pick up. The best part is, our GMC Sierra 1500 Fuel Pump products start from as little as $79.99.

When to know if your GMC Sierra fuel pump is bad?

If your car isn’t starting at all, and you hear the fuel pump prime that is usually a good indication that the pump is working to some capacity. Testing your Sierra’s fuel pressure on each side of the pump would be the best way to diagnose this problem.

How to check fuel pump signal in gmflash?

1. CONNECT PIN1 (BLACK GROUND) TO PIN16 (PINK GROUND) 2. CONNECT PIN32 (RD/WH BATT + ) TO PIN47 (GY FUEL PUMP 12+) THIS WILL POWER THE PUMP TO RUN AND CHECK FOR A FAULTY FUEL PUMP. 3. NEXT, CHECK FOR FUEL PUMP SIGNAL AT THE FUEL SYSTEM CONTROL MODULE. 4. FIND THE DARK GREEN/WHITE WIRE IN PIN13.

How to check for a faulty fuel pump?

THIS WILL POWER THE PUMP TO RUN AND CHECK FOR A FAULTY FUEL PUMP. 3. NEXT, CHECK FOR FUEL PUMP SIGNAL AT THE FUEL SYSTEM CONTROL MODULE. 4. FIND THE DARK GREEN/WHITE WIRE IN PIN13. WITH A TEST LIGHT CONNECTED TO THAT WIRE, TURN THE KEY TO THE RUN POSITION.

When did the GMC Sierra truck come out?

The GMC Sierra is the fifth-most popular truck in the United States, with more than 230,000 trucks sold in 2019. General Motors introduced the GMC Sierra and its twin, the Chevrolet Silverado, in 1998.

What do GM genuine parts fuel pump assemblies do?

GM Genuine Parts Fuel Pump Module Assemblies are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These module assemblies help deliver fuel to your vehicle’s fuel injectors, providing a steady, reliable fuel supply to your vehicle’s engine.

What are the symptoms of a bad fuel pump?

Also, the symptoms are almost exactly the same as bad/clogged fuel filter. Here are the most common symptoms of a bad fuel pump in your GMC Sierra: One of the most common signs that a fuel pump is going bad is a whining sound. The whining sound can indicate that the fuel pump is going out before there are any performance based issues.

Navigation