How to remove the clutch basket on a Harley Davidson?
This helps you to work cleaner, without so much residual oil hanging around. Next, remove the outer primary cover & gasket and slacken the clutch cable. Loosen the jam nut and back off on the Harley clutch adjustment at the clutch pack. Remove the adjuster plate retaining clip to expose the mainshaft/clutch hub nut.
How do you remove clutch plates on a motorcycle?
Now remove the the clutch plates. On some clutches you pull the plates and the inner clutch basket as a unit after removing the nut or circlip holding it on. On others, you remove an outer clutch plate/spring carrier and then pull out the plates individually. There may be large rubber rings or large flat spring like things between the plates.
How do you get the clutch basket off a triumph?
The BSAs and Triumphs require a special puller to get the clutch basket off. All clutches must have a bit of free play in the cables and rods so the clutch springs can exert the maximum amount of pressure on the plates.
What should I do if my Clutch on my motorcycle is bent?
Turn them on edge, both fiber and steel plates. If they are bent replace them. Look at the inner and outer fingers. If they are damaged or worn, replace them. Look at the clutch basket. Inspect the grooves the clutch plate fingers slide into. Both inner and outer. if they are badly worn, consider replacing the clutch basket.
This helps you to work cleaner, without so much residual oil hanging around. Next, remove the outer primary cover & gasket and slacken the clutch cable. Loosen the jam nut and back off on the Harley clutch adjustment at the clutch pack. Remove the adjuster plate retaining clip to expose the mainshaft/clutch hub nut.
Why does my washer spin when the basket is full?
The washer clutch assembly releases the drive system’s brake to allow the basket to spin during the spin cycle. If the washer spins when the basket is empty but not when it’s full, the clutch assembly could be the problem (another problem could be the clutch band ).
How do you remove a clutch retainer from a car?
Pull the thrust washer off of the transmission shaft. Using needle-nosed pliers, pull the clutch support ring off of the top of the clutch assembly. Using a slot screwdriver, pry the clutch retainer ring off of the top of the clutch assembly.
What causes the clutch to oscillate during spin?
Running the machine with an unbalanced load causes the tub to oscillate erratically during spin and creates an imbalanced load on the clutch. A quick eyeball test for the clutch is to lean it back and inspect the area around the gearcase and clutch for oil.
Can a stock clutch assembly be installed on a Harley?
It withstands the most extreme conditions where the stock Harley clutch assembly falls short, or down right fails. Before installing the Barnett assembly, we have to get into this drive and put the stock assembly on the bench.
What kind of basket does a Harley Davidson use?
Barnett’s basket is made to handle the harsh conditions or abuse that this drive is subject to. It withstands the most extreme conditions where the stock Harley clutch assembly falls short, or down right fails.
What to do if your clutch basket breaks?
The basket can break and / or start to crack. When you are servicing the primary, do thorough visual inspection of the basket for cracks. This will help in avoiding breakage and the related damage that chunks of aluminum can do to other primary components. Get in front of the issue and upgrade your basket.
It withstands the most extreme conditions where the stock Harley clutch assembly falls short, or down right fails. Before installing the Barnett assembly, we have to get into this drive and put the stock assembly on the bench.
What should I do if my clutch fails on my Harley?
He rider can use lighter springs for normal street riding, ride to the drag strip, put in heavier springs for racing, switch back to softer springs and ride home. The clutch is designed so that a steel plate installs last to isolate the pressure plate from wear.
What’s the best way to clean a Harley Davidson?
It is always a good idea to let the drive compartment drain overnight, if possible. This helps you to work cleaner, without so much residual oil hanging around. Next, remove the outer primary cover & gasket and slacken the clutch cable. Loosen the jam nut and back off on the Harley clutch adjustment at the clutch pack.
It is always a good idea to let the drive compartment drain overnight, if possible. This helps you to work cleaner, without so much residual oil hanging around. Next, remove the outer primary cover & gasket and slacken the clutch cable. Loosen the jam nut and back off on the Harley clutch adjustment at the clutch pack.
Barnett’s basket is made to handle the harsh conditions or abuse that this drive is subject to. It withstands the most extreme conditions where the stock Harley clutch assembly falls short, or down right fails.
Why do I need to replace my clutch basket?
In terms of clutch basket wear, the main grounds for replacement of the basket are worn and grooved basket fingers. Notching on basket tangs is typically part of normal wear and is the main reason to warrant basket replacement.
What kind of clutch does a 98 XL1200 have?
Note : Unless noted otherwise, the engine below is a 98 XL1200S that has been upgraded to 1250 with a Buell XB crankshaft and respective engine sprocket. Loosen the nuts / bolts holding the engine sprocket and clutch basket on. The engine sprocket has right hand threads and the clutch basket has left hand threads.
How do you get the clutch out of an Evo?
Pull the clutch basket out as far as possible and then maneuver your fingers both hands under the engine sprocket. Rock it side to side while pulling outward. Slowly you can rock it out enough to get your fingers under it to move it out far enough to release the force generated by the magnets.
Is the small clutch adjustment cover round or round?
On the 1991-1993 cover, the primary chain inspection cover is also round, but is mounted with two screws. Likewise, the small clutch adjustment cover is round and mounted by two screws. On the 1994-2003 cover, the primary chain inspection cover is still round using two screws to mount it.
Note : Unless noted otherwise, the engine below is a 98 XL1200S that has been upgraded to 1250 with a Buell XB crankshaft and respective engine sprocket. Loosen the nuts / bolts holding the engine sprocket and clutch basket on. The engine sprocket has right hand threads and the clutch basket has left hand threads.
Pull the clutch basket out as far as possible and then maneuver your fingers both hands under the engine sprocket. Rock it side to side while pulling outward. Slowly you can rock it out enough to get your fingers under it to move it out far enough to release the force generated by the magnets.
On the 1991-1993 cover, the primary chain inspection cover is also round, but is mounted with two screws. Likewise, the small clutch adjustment cover is round and mounted by two screws. On the 1994-2003 cover, the primary chain inspection cover is still round using two screws to mount it.
Are there replacement parts for the Harley Davidson Electra Glide?
We stock more than eight million parts, accessories, gear, and apparel products to meet all your riding needs. For regular maintenance and repairs, or if you’re just looking to keep your ride in original factory condition, we have Harley-Davidson Electra Glide replacement parts on sale.
How do you install a clutch on a Harley Davidson?
After the Harley clutch bearing is fully seated, inspect it for any binding or rough feel. Install the retaining ring with the tapered side facing out (flat side against the bearing) and the bearing installation is complete. Next, we will go back to the press to install the Scorpion clutch hub into the bearing/basket.
What should the clutch bearing be on a Harley Davidson?
Take your time setting up. It is of utmost importance that the Harley clutch bearing is started straight and that the basket is supported properly. Support the inner dimension of the basket. If you support the basket on it’s outer edge, the basket will break. Press against the bearings outer race and on it’s numbered side.