When to change the light bulb in the trunk?
Car trunks are lit by a trunk light for both convenience and safety. Replacing a bad bulb is important for nighttime emergency roadside situations. This step-by-step guide will outline how to change the light bulb (or bulbs) in your vehicle’s trunk or cargo area when your current bulb has failed.
How do you replace a light bulb in a car?
Use a flashlight if necessary to find the light bulb. Step 3: Remove the trunk light bulb housing. Use a flathead screwdriver, or your fingernail if you can, gently get under the lip of the housing along each side. Be gentle and patient, and the side that wants to come out first will start to come loose.
How do you replace a type 2 light bulb?
Type 2 has a cylinder shape and is connected by two clips or spring-loaded tabs. Once you have inserted the new bulb, replace the housing into the vehicle by gently guiding and pressing it back into place. Step 2: Reconnect the battery and test the new bulb.
Can a rear hatch light be swapped with LEDs?
If you are looking to increase the brightness of your hatch lights, you may want to swap them out with LEDs. Beyond increasing the brightness, your color will change from yellow and dim orange to a crystal bright write color. The color of LEDs looks much better. The rear hatch and trunk area is one of the most important areas to light up.
Car trunks are lit by a trunk light for both convenience and safety. Replacing a bad bulb is important for nighttime emergency roadside situations. This step-by-step guide will outline how to change the light bulb (or bulbs) in your vehicle’s trunk or cargo area when your current bulb has failed.
Use a flashlight if necessary to find the light bulb. Step 3: Remove the trunk light bulb housing. Use a flathead screwdriver, or your fingernail if you can, gently get under the lip of the housing along each side. Be gentle and patient, and the side that wants to come out first will start to come loose.
Type 2 has a cylinder shape and is connected by two clips or spring-loaded tabs. Once you have inserted the new bulb, replace the housing into the vehicle by gently guiding and pressing it back into place. Step 2: Reconnect the battery and test the new bulb.
If you are looking to increase the brightness of your hatch lights, you may want to swap them out with LEDs. Beyond increasing the brightness, your color will change from yellow and dim orange to a crystal bright write color. The color of LEDs looks much better. The rear hatch and trunk area is one of the most important areas to light up.
What to use to replace car trunk light bulb?
Use a box end or socket wrench to disconnect the clamp holding the negative battery cable to the negative terminal on the car battery. This will prevent you from blowing a fuse, but it is also a good habit to develop as a first step to any service or repair involving an electrical part on your vehicle.
What do you use to pull light bulb out of socket?
Use latex or rubber coated gloves to gently pull the light bulb out of the socket. If you try to do this with bare fingers, the oil in your hand may make it slip, and in the off-chance that you squeeze the bulb too hard and break it, you are less likely to cut yourself while wearing gloves.
Use a box end or socket wrench to disconnect the clamp holding the negative battery cable to the negative terminal on the car battery. This will prevent you from blowing a fuse, but it is also a good habit to develop as a first step to any service or repair involving an electrical part on your vehicle.
Use latex or rubber coated gloves to gently pull the light bulb out of the socket. If you try to do this with bare fingers, the oil in your hand may make it slip, and in the off-chance that you squeeze the bulb too hard and break it, you are less likely to cut yourself while wearing gloves.
How do I change the tail light bulb on a Chevrolet Spark?
Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.