Where is the VSS sensor on a Honda?
Open hood and locate the VSS. It is in the back of the engine compartment on top of the transmission. Remove the air intake hose and filter. Remove the electrical connector on top of the VSS by squeezing the clip and sliding it off of the sensor.
What causes a Honda Civic speedometer to stutter?
If one or both oxygen sensors malfunction, incorrect ignition and fuel supply could cause the engine to run poorly, which will cause the speedometer to jerk and stutter in response. A bad oxygen sensor is often accompanied by the check engine light.
Can a speed sensor be removed from a 1998 Honda Accord?
A light source will come in handy. The 98 Honda Accord VSS is easier to get to if you take off the air intake hose and filter. One screw holds the sensor in place and it has an electrical connector on the top. After removing the electrical connector, remove the screw. Once the Screw is out you can remove the Speed Sensor.
Why are there two oxygen sensors in a Honda Civic?
Unlike most other cars, the Honda Civic has two oxygen sensors, which relay exhaust information to the car’s computer so that the fuel supply and ignition rate of the engine remain stable and efficient.
Open hood and locate the VSS. It is in the back of the engine compartment on top of the transmission. Remove the air intake hose and filter. Remove the electrical connector on top of the VSS by squeezing the clip and sliding it off of the sensor.
If one or both oxygen sensors malfunction, incorrect ignition and fuel supply could cause the engine to run poorly, which will cause the speedometer to jerk and stutter in response. A bad oxygen sensor is often accompanied by the check engine light.
Unlike most other cars, the Honda Civic has two oxygen sensors, which relay exhaust information to the car’s computer so that the fuel supply and ignition rate of the engine remain stable and efficient.
A light source will come in handy. The 98 Honda Accord VSS is easier to get to if you take off the air intake hose and filter. One screw holds the sensor in place and it has an electrical connector on the top. After removing the electrical connector, remove the screw. Once the Screw is out you can remove the Speed Sensor.
How to change the speed sensor on a Honda?
Insert the drive link into the new VSS and plug it in. The drive link should line up with the shaft, and you will hear a click when it is in place. Tighten the VSS with the 10 mm bolt, and reattach the connector. It will click into place. Replace air intake hose and filter. Figure 1. A vehicle speed sensor (VSS). Figure 2. Location of the VSS.
How to tell if your Honda VSS is faulty?
Here are some signs that the VSS might be faulty: 1 The speedometer behaves erratically. 2 The check engine light turns on intermittently and sporadically during acceleration. 3 The brakes are sometimes harder to engage than normal. 4 The transmission revs higher before it changes gears. More …
Where is the VSS on a Honda Accord?
Open hood and locate the VSS. It is in the back of the engine compartment on top of the transmission. Remove the air intake hose and filter. Remove the electrical connector on top of the VSS by squeezing the clip and sliding it off of the sensor. Remove the VSS bolt with a 10 mm socket, ratchet, and extension.
What does it mean when your speed sensor says p0500?
If the reading does match but you still have a P0500 code, you likely have an intermittent problem. If your vehicle fails the test listed above, it’s time to determine what part of the VSS circuit is to blame. Testing the sensor varies slightly, depending on which type of sensor your vehicle uses.
How is the vehicle speed sensor ( VSS ) used?
As you can probably guess, the vehicle speed sensor (VSS) is used to determine vehicle speed. This information is used by various ECUs throughout the vehicle, including the PCM and TCM. The PCM uses the VSS signal to determine the control of outputs such as EGR function and speedometer operation.
How to check VSS code on reed switch sensor?
If the VSS checks out OK, but you still have P0500 code illuminated, you’ll need to check the sensor circuit. Reed switch sensor: A reed switch VSS circuit is pretty simple. The sensor will have two wires going to it: power and the return signal to the PCM.
What are the different types of speed sensors?
There are three types of vehicle speed sensors: magnetic pickup, Hall Effect and reed switch: Reed design: opens and closes a circuit as it’s rotated to produce a digital signal.