How to replace front brake pads on Volvo S40?
Follow this 7 steps tutorial to replace the front brake pads on your Volvo S40 or V40 (1995 to 2004) Tools Needed: 12 and 15 mm spanner, and caliper wind tool. Step 1. Jack your car up and make sure that it is securely supported. Step 2. Remove the front wheel. Step 3. With a 12mm spanner remove the lower bolt securing the caliper.
How big are the brake pads on a Volvo?
Make sure you know what hub/rotor you have. Finally, your minimum permissable pad thickness, when you are checking pads, is 3 millimeters per Volvo specs for the front pads and 2 millimeters for the rear.
What are the brake problems in a Volvo?
Troubleshooting: Low Pedal and Soft Brakes Problems Hard Pedal Problems and Brake Booster Diagnosis Brakes Pull When Applied: Control Arm Bushings Brake Calipers Rattle on Mounting Bolts Pulsating Brakes: Runout in Hub and Rotor Intermittent Brake Failure: Bad Sensor Seal Wheel Shudder: Diagnosis Brake Shuddering and Suspension Bushings
Where are the brake calipers on a Volvo 700?
Brake Torques Table Component Identification: Brake Caliper Identification. Front Calipers: [Editor:] Volvo 700 cars use a variety of calipers, rotors, and pads on the front hubs. Prior to working on the brakes, carefully identify which components you have so that you can acquire the correct parts.
What are the brake rotors on a Volvo?
740 w/ Girling ABS 91-92 front 900 w/Girling ABS 91-on front Rear Pads Photo Details REPCO 102 700/900 w/ ATE rear REPCO 3067 760 Girling w/ IRS rear. 900 Girling w/ IRS rear Brake Rotor Identification.
Is there a reset tool for rear brake pads?
Brake pad design configuration may vary slightly, but the concept is the same. A rear caliper reset tool is necessary for parking brake integrated systems. The reset tool screws the piston back into the caliper. These calipers cannot be compressed with a clamping tool, it can only be reset with the reset tool.
How to change brake pads with an electric parking brake?
1. Connect a car battery charger 2. Connect a diagnostic tool 3. Replace brake pads and push back pistons 4. Press the foot brake pedal 5. Connect the diagnostic tool again 6. Set a basic Setting 7. Test the electric parking brake function You are done! How do I know if I need a computer to replace my rear brake pads?
How do you reset a rear brake caliper?
A rear caliper reset tool is necessary for parking brake integrated systems. The reset tool screws the piston back into the caliper. These calipers cannot be compressed with a clamping tool, it can only be reset with the reset tool. A locator slot is used on the inboard piston, which is fitted into a peg located on the backing plate of the pad.
What kind of brake disc does a Volvo V40 use?
On the local italian Volvo forum, some V40 CC users with 320mm discs, “complains” about such behaviour because they can drive both 300mm and 320mm equipped V40s, they say that the 320mm discs provide a great stopping power and they need to gentle press the brake pedal to avoid any “grabbing”. Yet they also say the 300mm discs are a bit “weak”.
What’s the tightening pattern on the brake discs?
The tightening pattern is 1-3-5-2-4). The discs are held on by a large countersunk Torx screw, which is pretty tight. Ideally you would loosen this with the handbrake on, but you can’t really do that when you are doing them 1 at a time using a jack.
What kind of lubricant to use on brake pads?
The pads already have an anti-squeal soft plastic backing on them. The only place VIDA shows putting any lubricant is using silicone grease on the channels on the camiper carrier the pad locating tabs slide in.