What are the codes for a Cummins Engine?
115 Engine Magnetic Speed/Position Lost Both of Two Signals – Data Erratic, Intermittent, or Incorrect 122 Intake Manifold 1 Pressure Sensor Circuit – Voltage Above Normal, or Shorted to High Source
What kind of engine does a Cummins 6.7L have?
The 6.7L Cummins engine had a high-pressure Common Rail fuel injection system, electronically controlled fuel injection pump, and new equipment for emissions reduction. The new version was designed guided by stricter requirements on Federal emissions regulations.
Are there any problems with the Cummins 6.7 ISB engine?
The 6.7 ISB has become the most reliable Cummins B engine to date. In stock form, the failure rates are meager. The common problems are related to emissions equipment and common rail injection. The EGR system is prone to clogging and that issue is typical to all engines equipped with EGR.
What is the fault code for a Cummins M11 engine?
Just select your engine to see descriptions of each fault code for your particular Cummins ECM. Celect Codes – Includes N14, M11 & L10 engines up to 1995.
What does it mean when fault code 1922 is active?
• Excessive ash in the DPF • If both Fault Code 1921 and 2777 are inactive with an active Fault Code 1922, this indicates that a regeneration inhibit message has been received by the engine ECM and that active regeneration of the aftertreatment diesel particulate filter was not allowed.
What is the fault code for a Cummins forklift?
195-2wire Coolant Level Sensor 1 Circuit – Voltage Above Normal, or Shorted to High Source 195-3wire Coolant Level Sensor 1 Circuit – Voltage Above Normal, or Shorted to High Source 196-2wire Coolant Level Sensor 1 Circuit – Voltage Below Normal, or Shorted to Low Source
What are the fault codes on a Kenworth Truck?
Circuit Number……….17 = Starter Solenoid. Destination or Purpose…. SR = Starter. 3211 Powertrain, Exhaust Functions, Aftertreatment, Exhaust Inlet Temp. Sensor 3212 Powertrain, Exhaust Functions, Aftertreatment, Exhaust Mid Temp. Sensor 3213 Powertrain, Exhaust Functions, Aftertreatment, Exhaust Outlet Temp. Sensor
When did Cummins start issuing ISX fault codes?
These codes pertain to the ISX engines built between 2007 and 2010. These engines are easily identified by having a DPF and regen on a regular basis. These codes do NOT pertain to engines using DEF.
What kind of engine does a Kenworth T800 have?
2016 kenworth t800 day cabs, cummins isx 450 hp, engine brake, 10 speed ultrashift, 14,300/46,000 axles on air ride with full locking 3.73 ratio, air slide 5th wheel, 3 line wet kit, chrome bumper,… see more details
What is the aftertreatment temperature on a Cummins?
1667 Aftertreatment Exhaust Gas Temperature 1 – Data Erratic, Intermittent, or Incorrect 1674 Aftertreatment Exhaust Gas Temperature 2 Circuit – Voltage Below Normal, or Shorted to Low Source
What is the ISX fault code for Cummins CM871?
Here are all the Cummins ISX engine fault codes available for the Cummins CM871 ECM. These codes pertain to the ISX engines built between 2007 and 2010. These engines are easily identified by having a DPF and regen on a regular basis. These codes do NOT pertain to engines using DEF.
How to check the DTCs of a Cummins Engine?
To check the DTCs of the electronic fuel supply system and the engine protection system, turn the diagnostic key to the OFF position and the diagnostic switch to the ON position. Turn the car key to the ON position. If there are no active DTCs recorded, the yellow and red indicators will not appear.
What are the symptoms of a failing 6.7L Cummins fuel control actuator?
What are the symptoms of a failing 6.7L Cummins Fuel Control Actuator? Rattling Noise from the engine, which sounds like Fuel Knock. It decreased the engine power output level. Engine operation is rough. Engine RPM surging. A surging or loping idle. A faulty fuel pressure regulator causes these symptoms.