What are the bolt torques on a Cat C13?
CAT C13 Main Bearing Bolts S/N – JAM1-UP S/N – KCA1359-UP S/N – KCB6818-UP step 1 = 150 +- 7 Nm, 110 +- 5 lb.ft step 2 = + 60 degrees S/N – KCA1-1358 S/N – KCB1-6817 step 1 = 50 +- 5 Nm, 110 +- 4 lb.ft step 2 = + 60 degrees Click for CAT C13 engine manuals and specs
What should the oil pressure be on a Cat C13?
Cat C13 low oil pressure. Minimum is 10 psi at idle. But minimum psi above 1800 is 40 psi. It sounds like your oil pressure is to low. This is a common problem on the C13 engines. There are two things I have seen cause low oil pressure. The first and most common is a faulty relief valve in the oil filter base. I see this a lot.
What are the dimensions of a Cat C13?
CAT C13 Dimensions approx Dimensions length 1280 mm, 51 in width 1090 mm, 43 in height 1220 mm, 48 in Click for CAT C13 engine manuals and specs. CAT C13 Weight approx Weight 1184 kg 2610 lb Click for CAT C13 engine manuals and specs. CAT C13 Compression ratio 17.3:1 Click for CAT C13 engine manuals and specs.
What is the Flash code for a Cat C13 motor?
I have a 2005 Peterbilt with a cat c13 and I have the following code: intake valve actuation system oil pressure voltage high. PID 385 FMI 3 FLASH CODE 95 … read more Hello, I have a oil pressure concern with a C13 motor. This Hello, I have a oil pressure concern with a C13 motor. This motor is a 2005 motor installed in a MCI motorcoach.
How much torque does a Caterpillar C15 engine have?
CATERPILLAR C15 Essential Diesel Engine Bolt Tightening Torques CAT C15 Main Bearing capscrews step 1 = 95 Nm, 70 lb.ft step 2 = 260 Nm, 190 lb.ft
Where do I Find my flange bolt torque?
All values other than suggested torque amount are sourced directly from flange bolt charts and flange torque charts in the ASME B16.5 “Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard” (2017).
How to calculate torque for ASTM A193 B7 flanges?
Use the following Torque Calculator for ASTM A193 B7 and ASTM A320 L7 bolting, as specified in API 6A, 16A and 17D for flanges. TPI for 1″ and smaller are UNC, 1-1/8″ and larger are 8 UN. Some flanges can be over-tightened to the point that the ring groove or the flange can be damaged.
How to calculate the torque of an API bolt?
Enter 105000 for B7/L7 standard bolting. Enter percent of bolt Yield Strength. 50% specified by API 6A. 70% specified by API 17D. Modified bolting used in many API flanges requires de-rating. Reference API Spec 6A to identify these flanges and determine their de-rated working pressure.
What are the specs of a Caterpillar C13 diesel?
CATERPILLAR C13 Diesel Engine Specs. CAT C13 Arrangement, displacement, bore and stroke Arrangement 6 cylinder in-line turbo, aftercooled Displacement 12.5 liter, 763 CID Bore 5.12 in, 130 mm Stroke 6.18 in, 157 mm Click for CAT C13 engine manuals and specs.
Why is Cat C13 ACERT diesel engine optimized?
Fuel consumption optimized to match operating cycles of a wide range of equipment and applications while maintaining low operating costs.
When to change the thermostat on a cat engine?
If it’s running below 185 degrees F, change your thermostats. (Cat engines usually have two or four thermostats per engine. If one fails, change all of them.)
What to do if a head gasket fails on a caterpillar C10?
If a head gasket is the source of the problem this revised cylinder head torque procedure can eliminate repeat head gasket failures on Caterpillar C10 and C12 diesel engines. Replace all cylinder head bolts with p/n 129-3184, reduced shank bolts.
How to eliminate head gasket failures on Cat Diesels?
Q. To eliminate head gasket failures on Cat diesels, how should the heads be torqued? A. Pressurizing the cooling system with the oil pan removed can differentiate between a water pump leak and a cylinder head gasket leak before removing the head.
Is there a serial number for the cat C10?
Caution: Bolt Torques and other data, may vary from serial number to serial number, please check the manuals.
What does the initial torque do on a fastener?
There is an initial torque and an additional turn. The initial torque is required to bring all parts of the joint into contact. The additional turn provides the desired clamping force. Ensure that all fasteners have been torqued before you perform the additional turns. Turn the fastener according to the specified amount.
How big is a Caterpillar CAT C11 diesel engine?
CAT C11 Dimensions approx: length 1297 mm, 51 in width 1050 mm, 48 in height 1217 mm, 49 in CAT C11 Weight approx: 1030 kg 2270 lb CAT C11 Compression ratio mostly at 17:1 CATERPILLAR C11 Diesel Engine Spec Sheets
Where are the 3 bolts on a jake brake housing?
These 3 bolts must be used in the third hole from the front on each jake brake housing. Otherwise to install the heavier 6 point bolts in this position will starve the jakes for oil and keep them from functioning properly.
What are the torque specifications for a car?
The specified amount will normally be in 30° increments. Turns of 120° or 180° are preferred. Turns of 120° or 180° are easily measured by the points of the hex head of the fastener. Lubrication may be specified in order to reduce the effort that is required for the final turn.
What are the different types of ARP flywheel bolts?
ARP offers two styles of Flywheel bolts: premium grade Pro Series, with a 200,000 psi rating and High Performance, with a 180,000 psi rating. They are both heat-treated prior to thread rolling and machining, feature an exclusive, flat, 12-point head design and larger than stock shank diameter for increased strength and improved flywheel register.
How big is the thread on a flywheel bolt?
NOTE 1: All flexplate bolts listed below are Pro Series 200,000 psi rated bolts unless noted otherwise. NOTE 2: The thread size of metric fasteners is listed using international designations. For example, “M10” indicates a 10mm thread size. Didn’t find the kit you were looking for?
CAT C13 Dimensions approx Dimensions length 1280 mm, 51 in width 1090 mm, 43 in height 1220 mm, 48 in Click for CAT C13 engine manuals and specs.
What’s the best way to install cat bolts?
Clean all surfaces of rust, paint, nicks, and burrs. Install bolts first in the center and work out toward the edge. Tighten all bolts to the specified torque (see chart below for specifications). Set bolt heads firmly into the edge countersink using a heavy hammer. Safety glasses MUST be worn when striking bolt heads.
What kind of strength does cat bolts have?
Cat® Bolts are engineered to exceed SAE Grade 8 standards and ISO 10.9 strength specifications for longer wear life and improved reusability.
What kind of torque does a Chevy small block have?
900 101.69 Chevy Small Block – 7/16 in. Bolt – Rod Cap Type: 75 900 101.69 Chevy Small Block – 25-50-75 Step – Not Outer Bolts Type: 65 780 88.13 Chevy Small Block – Outer Bolts on 4 Bolt Cap Type: 65 780 88.13 Chevy Small Block – 25-45-65 Helical Sequence Type: Distributor Clamp To Engine Block 20 240 27.12 Type: 20 240 27.12 Type: 35 420 47.45
What kind of torque does a 5.0L 305ci have?
Type: 75 900 101.69 Chevy Small Block – 25-50-75 Step – Not Outer Bolts Type: 65 780 88.13 Chevy Small Block – Outer Bolts on 4 Bolt Cap Type: 65 780 88.13 Chevy Small Block – 25-45-65 Helical Sequence Type: Distributor Clamp To Engine Block 20 240 27.12 Type: 20 240 27.12 Type: 35 420 47.45 Type: Engine Temp Sensor To Intake Manifold 20 240 27.12
Where are the bearings located on a piston and cap?
The grooves in the rod and cap and the tangs on the bearings merely serve as an installation aid in order to align the bearings during assembly (locating upper and lower bearings correctly fore/aft). Bearings as-installed feature the ends slightly protruding beyond the parting line.
Is there a Caterpillar C13 ACERT engine for sale?
2006 CAT C13 Acert .430 HP Used Diesel Engine for Sale, Tested and inspected with 90 day warranty. Call or visit our website for more information! CAT C-13 ENGINE ASSEMBLY.
Where can I buy a 2008 Cat C13 engine?
Equal opportunity lender. 2008 CAT C13 used diesel engine for sale .470 HP, tested and inspected with warranty. Call or visit our website for more info..
What makes a Caterpillar C13 diesel engine so good?
World-class manufacturing capability and processes coupled with proven core engine designs assure reliability, quiet operation, and many hours of productive life. Simple and efficient turbocharger with balance valve provides optimal air management and improved fuel efficiency.
What to use to replace head gasket on Caterpillar CAT engine?
Use an M16 X 2 (8T-3096) bottoming tap to clean the 26 bolt holes in the block to allow the head bolts to produce the correct clamping load. If threads in the cylinder block are damaged, Caterpillar recommends a Heli-coil® insert (p/n 1084-16CN-32) for these engines. Use only the revised reduced wrap fire ring head gaskets.
How do you install a cat compression brake?
In order to install the valve actuator group for the compression brake to the cylinder head, place the housing over the mounting studs. Finger tighten the mounting stud nuts and the mounting bolt. 2. Tighten the nuts, the bolt and flange nuts of each valve actuator group in the numerical sequence that is shown in Illustration 1. 3.
How to set Jakes on a Cat C13 overhead?
Set valves and injectors on TC compression, rotate 360 to TC exhaust, set valves and injectors. Install jakes and VVA housings. Set 3-5-6 VVA and 2-4-6 exhausts. Rotate 360 again then do 1-2-4 VVA and 1-3-5 exhaust.