Why does my C15 Cat truck not start?
Check valve would be the likely cause for the “won’t start after a day or so” but shouldn’t account for the “starts, runs for a minute or so then quits” and does this twice back to back. All the valves do is hold pressure/ prime when it’s not running.
Why does my Peterbilt truck won’t start?
When I try to start it does nothing at all. But if I take the female plug that goes in to the relay box on the firewall out and run a wire across it the truck starts perfectly which rules out the starter or batteries being bad. I’m guessing it’s the ignition but I’m just trying to get some input
How often does a cat C15 engine die?
Lately, it’s also been real bad about losing prime, so about one out of ten times I start it up, it loses prime and dies, then I have to use starting fluid to get it started again. I’ve had it in the shop, both Cat and Peterbilt, more than 25 times, every test in the world has been run on it, and no one can figure it out.
What to do if your cat C15 engine is leaking?
Air might also be found on the return line to the tank, but be careful as some bubbles in the fuel is normal. Try pressurizing your fuel supply lines/fittings with shop air and check for leaks with soapy water. No codes or engine light (even intermittently)……. right?
What to do if your truck wont start?
When I tried to start it, it wouldn’t. Engine would crank over fine, but wouldn’t fire. I gave it a shot of starting fluid and it would run til it was gone and quit. I removed the spin on fuel filter and replace it with a spin on block off plate, drained a bit of fuel from the Davco (no water).
What to do if your cat wont start?
No point climbing around under the truck if its at a filter housing or the lift pump. silver dollar and Vampire Thank this. If you see any dirt on the lines that should be where the fuel is leaking from. Good luck. silver dollar Thanks this. Sounds like it could be your check valve getting weak. silver dollar Thanks this.
Are there any problems with the C-15 cat?
C-15 Cat Engine Problems. Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by dave_0755, Nov 4, 2010 . I’m hoping someone with knowledge of the C-15 can help.
How much power does a C-15 cat engine have?
No disrespect but chances are this guy does not own an Acert! They are made to be lugged, all the way down to 1100 rpm. It’s not the same as an “E” or the first C15’s (6nz) there is absolutely no power above 1500 and running one there will do nothing but burn fuel.
Why did cat insist on learning to drive the ACERT?
There is a reason Cat insisted on drivers learning how to drive the Acert’s, and they insisted you have to gear them right.
How to troubleshoot a C13 or C15 engine?
A.Crank the engine and observe the engine speed on the Cat ET status screen. Refer to Troubleshooting, “Speed/Timing – Test” for additional information. Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal.
Why did my C-15 twin turbo engine go bad?
Had an ecm go bad on our 2005 C-15 Twin turbo, cost was about $2100 to replace at dealer and take a look at fuel line that runs behind ECM they will rub computer from vibration and chafe the line and leak, Put some insulation on it after repair.
Why does my cat engine won’t start?
Cat Engine Won’t Start Troubleshooting. Diesel Engine Crank No Start. – YouTube Cat Engine Won’t Start Troubleshooting. Diesel Engine Crank No Start. If playback doesn’t begin shortly, try restarting your device.
What to look for when your engine won’t start?
Check for a blown fuse that may be preventing a circuit from working properly, like the fuel injection or computer system. To operate efficiently, an internal combustion gasoline engine needs a good spark, the right amount of fuel, and good compression (a healthy mechanical condition).
Why does my car not start when I crank the engine?
If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.
Why is the Check Engine light not coming on?
Even if the check engine light hasn’t come on, you may find a pending code that can guide you in your diagnosis. False input or lack of input from sensors like the crankshaft position sensor (CKP) or camshaft position sensor (CPS) can prevent the engine from starting.
What does it mean when engine cranks are abnormal?
Upon initial cranking, the status for engine speed may indicate that the engine speed signal is abnormal. This message will be replaced with an engine speed once the ECM is able to calculate a speed from the signal. Result: The timing sensor is operating properly. Proceed to Test Step 8.
What to do if your engine cranks but not starts?
Loosen the high pressure line at two injectors and visually check fuel delivery while cranking the engine. Replace injection pump, if fuel is not being delivered. Check the injection pump timing.
Can a 2003 Cummins have a hard start?
One of the most common calls we get are from customers with a 2003-2007 Cummins that have developed either a hard start or no start condition. In order to help out, we had our very own Tyler Lucas, put together this step by step tutorial that you will hopefully find insightful.
Why does it take so long to start a 300K engine?
Sure why not. On high mileage engines (200k to 300k) the pistons ring can wear causing low compression which increases crank time and causes hard starting. This is because the compression ratio is low and it takes time for the engine to gain enough speed cranking by the starter to ignite the fuel air mixture.
What causes engine crank time to be extended?
Another common reason for extended crank time for engines is a vacuum leak. Engine vacuum must be a sealed system which the mass air flow and map sensors depend on to send feedback information to the main computer which in turn sets the stage for the engine starting sequence.
What does no start no crank no click mean?
If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that. In the old days, power flowed through the ignition switch and down to the starter solenoid. Not anymore.
What causes a C-15 cat engine to spin faster?
Downshift until you are pulling under 20 PSI on the manifold pressure and have your RPMs over 1600, this will cause the fan to spin faster and cool better. As for your fuel mileage, that is very common for an ACERT. Sounds like a typical ACERT to me.
When did Caterpillar switch to the ACERT engine?
They ran at high temperatures, guzzled fuel, and couldn’t pull very well. The Caterpillar C15 shifted over to the C15 ACERT in 2004. The term ACERT is an abbreviation for Advance Combustion Emission Reduction Technology. This engine mainly focused on the air and fuel systems in an effort to meet the strict EPA emission requirements set in 2002.
Why does my GM car say no start no crank?
How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.
Is the C-15 engine idled at 1000 rpm?
If you read your manual the c-15 should be idled at 1000 rpm if has to sit longer than 5 min. I have seen this before on a few Mack trucks in Australia.
What happens if the Check Engine Light is not on?
If a problem occurs but does not meet the software’s threshold for the number of times the problem must occur before lighting the check engine light, the trouble code may be stored as a PENDING CODE. In that case, you could scan the computer and find a code, even though the light wasn’t on.
Why does my car engine not want to start?
If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.
When did the Caterpillar C15 engine come out?
Caterpillar C15 Following the production of the 3406E, Caterpillar released the C15 in 1999. This engine is very popular because of its reliability and versatility. It’s so versatile in fact, that Cat lists over 34 applications that are powered by this engine.
Where can I buy a 2008 Caterpillar C13 engine?
2008 CAT C13 used diesel engine for sale . 470 HP, tested and inspected with warranty. Call or visit our website for more info. 2008 CAT C13 used diesel engine for sale . 470 HP, tested and inspected with warranty.
Is the Peterbilt 378 a day cab truck?
1996 peterbilt 378 heavy spec 3406e cat 475hp Dual frame 18spd eaton 1mil miles Dual line PTO Electric tarp hookup 3rd air line installed for lift gate 5th wheel lockable for end dump. Headache rac… See More Details
Which is better a C12 or C13 cat?
The turbos are horribly slow to kick in, and if your truck isn’t warmed up beyond about 160 degrees good luck getting a heavy load moving. The C12 was a much better motor. New Cat C13’s, even pre 2007, are only designed for fuel mileage. So screw it if it takes your truck 5 minutes just to get up to 65 MPH.
Is the C13 cat engine slow to wind up?
A 13 spd. would be my choice behind any engine. The c13 is slow to wind up but I found that if you just crack the throtle after a gear change and wait a second or two for turbo spool-up then squeeze on the pedal it really comes to life. If all you do is shift and mash then it wont pull or get any mileage.
Why does my ECM keep blowing out on my truck?
Driver went in pick up the truck it was running fine, after he was hooked to the trailer, truck stalled again, they took him back in the shop and came back telling me that ECM is blown because of corroded wire. my question is, why would truck start at and runs fine for the first time when he just fixed it with fuses and partial power wire to ECM.
What happens when an ECM loses ignition power?
If it losing ignition (or key) power the key on/off counter will increase. It helps to further diagnose power problems. Most ECMs have more than one power wire.
What to do if your ECM line is corroded?
We had a corroded power line to ECM he replaced it with a new fuses and patch of wire, a partial not the whole line.
Why does my GMC engine start but not run?
Repair guides and support for cars, trucks, and SUVs manufactured by GMC. Answered! View the answer I have this problem too Is this a good question? An engine will start but not run when the fuel runs out .