What is the pending fault code for Hino 268?
Air Tank Pressure is at 105, braking system is ok. – This code is the PENDING FAULT CODE (NO MIL). – This code is set when BCU detects low air pressure from the air tank. – BCU presume failure when 3 times low pressure events detected in a row. – If no P2431/P2636, this DTC can be ignored.
What does p0410 mean on a Hino truck?
P0410 doesn’t mean anything. It means that the air pressure in the tanks was low and it had to fill them up first before it could fire the burner to heat up the SCR. Go into the engine diagnostic menu, go to data monitor then activation test.
Where can I find a Hino service manual?
For General Information or Technical Assistance regarding your Hino Truck, please contact your local Certified Hino Dealer. If you need an Owner’s / Driver’s Manual or a Service Repair Manual, please visit the online Publications page . For all other General concerns, email us at: [email protected]
What to do if your Hino truck is under warranty?
If you are a current owner / operator of a Hino truck still under warranty and need emergency roadside assistance, please call HinoWatch on 1-866-365-HINO (4466) 24/7 Hino Blog!
How to know if your Hino truck has a fault?
Put a jumper on the “TE2” and “E1” terminals of the diagnostic connector. 4. Turn on the ignition. Note: the flashing of the lamp “CHECK ENGINE” confirms the inclusion of the test test. 5. Start the engine and drive at a speed above 5 km / h. 6. Create conditions for the failure (according to the owner). 7.
Where is the production series Code on a Hino truck?
This is located just below the VIN number on the VIN plate. The plate is attached to the passenger side doorjamb on all conventional trucks. The Production Series Code can also be found in Dealer Connect through the warranty screen. Go to DC600 then DC611 and then click on options.
Is the Hino 268 truck of the year?
These contributing factors helped earn the 268 the 2010 ATD Truck of the Year distinction. The 268 has helped Hino set a gold standard for moving and delivery trucks, among numerous other applications. TURBOCHARGED. INTERCOOLED. Award Winning Engines.
Where to find the Hino production series Code?
HINO Production Series Code In order to insure you are ordering the correct part number for the vehicle you are working on it is criti- cal that you use the Production Series Code. This is located just below the VIN number on the VIN plate. The plate is attached to the passenger side doorjamb on all conventional trucks.
Where can I get a Hino Truck Repair Manual?
This means more information for more accurate repairs. Hino Trucks dealers and body builders now have direct access to download 3D CAD models (.stp files) of all 2016MY and up conventional and COE chassis to be used for body design via a dedicated website www.hinocaddesign.com.
When is there no Ne signal on a Hino truck?
There is no “NE” signal to the electronic control unit for 2 seconds or more when the crankshaft is cranked by the starter. 1. Open or short circuit in the sensor circuit of the shaft speed sensor pump.
How many times does a Hino fault code flash?
6. For example, the lamp flashes 1 time, then a pause of 1.5 seconds, then flashes 3 times. This means code 13. 7. If two or more fault codes are stored in the memory of the electronic unit, the codes will be separated by a pause of 2.5 seconds.
What does a p204f Bank 1 OBD code mean?
When a code P204F is stored, it means that the powertrain control module (PCM) has detected a malfunction in the reductant portion of the selective catalyst reduction (SCR) system. Bank 1 denotes the bank of the engine that contains the number one cylinder.
How to know if your car has a p2436 code?
Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P2436 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
How much does a Hino dx2 cable cost?
Ordered Hino DX2 with Nexiq USB Link & ODB II Cable, with Hino Software. plus two days shipping total over 3000$ lets hope its worth the money… also bought a 3 days subscription and downloaded all the information i need.
What is the low temp code for p204f?
Pulled a P204F code. Low temp warning for the DEF. It was 80 Deg. out. Cleared it. Sat in truck again for 12 hrs. Got CEL light and truck said drive till regen is over. Shut off before regen over. Got up and drove home.
What does the p2047 code on a car mean?
What the P2047 code means. The P2047 code means a fault is present in the reductant injection valve circuit, bank 1 unit 1. The reductant injector is used to reduce emissions gases exiting the exhaust by injecting either air or chemicals depending on the usage and vehicle.
What kind of truck is the Hino 268A?
The 268A model is what it takes to support all of our traffic control and safety devices.” Strong, Straightforward, Dependable. Here’s a better way to build a cab – high visibility, great comfort and super low noise levels. All-in-all, it’s a great place for a driver to spend the day.
How to fix urea SCR on 2012 Hino?
Select ‘reset urea scr history’ and activate. It’ll take a few seconds, but then the warning on the dash does away and you can turn it off. To tell if it’s actually fixed, go to engine customization menu. Go to the last selectable line, it’ll say something like PM amount piling up. Type in 2.2 and click ‘Write’, ignition on, engine off.
How do you replace the burner on a Hino truck?
The parts replacement part of this can be accomplished by someone equipped with hand tools, a 27mm 12 pt socket, and a filter wrench. First, remove the right fender and expose the burner. Remove the ignitors wires. Twist them before pulling or you’ll rip their guts out.
What is the breather filter on a Hino burner?
This is the crankcase breather filter. It helps keep oil out of the intake. Just unscrew the cap, replace the element, and replace the O-ring on the cap. To reset the warning, the dealer or someone with the correct diagnostic software will have to connect to the ecu.
How do you reset the DPR on Hino?
Turn the key on, after the “Hino” logo fades press the “mode” button repeatedly until “Maintenance 1” is displayed. 2. Press the “select” button until the display shows “DPR” . 3.Press and hold the “Mode” and “Set Reset” buttons simultaneously for approximately 40 seconds to reset the “DPR Maintenance” Message.
What kind of malfunction is Def injector p2047?
P2047 is a def injector malfunction. Def usage varies widely. I wouldn’t worry about that part. A quick update on what i have done so far. Cleaned out Igniter and injection nozzle. Replaced DEF Pump filter.
What should I do if my Hino burner gets clogged?
Remove the pipe from the combustion air valve and burner and clean out that fitting and passage into the burner. This gets very clogged with schmoo over time. I forgot to mention to remember which ignitor came out of which hole. If the gap is too great, exchange them from side to side and remeasure the gap.