Is there a code 385-3 for cat C15?
Im working on a Cat C15. getting code 385-3 IVA pressure sensor high voltage. Tried replacing the sensor, worked for a couple days came back with same problem.
What does FMI 04 mean on a Caterpillar engine?
However, the FMI code 04 indicates that the voltage values are below acceptable values. The appearance of the FMI 04 code is most often associated with a malfunction of the signal circuits. The FMI code 04 is similar to the FMI 06 code and is sometimes used instead.
What’s the fault code on a cat C15?
Im looking for the Cat man.we have a c15 in the shop today that has a 385-5 code which is for IVA system oil pressure voltage high. The truck was … read more Vocational, Technical or Tra… I’ve got a c15 engine serial number NXS33019. With a 385-03 Hi I’ve got a c15 engine serial number NXS33019. With a 385-03 fault code.
What’s the IVA code for a cat C15?
Im looking for the Cat man.we have a c15 in the shop today that has a 385-5 code which is for IVA system oil pressure voltage high. The truck was … read more
What does code 385-3 Iva pressure mean?
Replaced sensor again, same issue, was good for a couple days and came back with code 385-3 active. we replaced the jumper harness from the sensor to the engine harness (right behind AC compressor) and still have the same issue.
Is there a problem with a 385-3 ECM?
If you have replace the sensor and the harness that connect to the sensor, you may have a faulty ECM. It’s rare but I have seen it two or three times over the years. Basically, a 385-3 is an open circuit. Most often the problem is the sensor. Since yours has been replaced several times. I would say the sensor is not the problem.
What does 26 U.S.Code § 385 mean?
26 U.S. Code § 385 – Treatment of certain interests in corporations as stock or indebtedness
How to get code 385-3 Iva pressure sensor?
Im working on a Cat C15. getting code 385-3 IVA pressure sensor high voltage. Tried replacing the sensor, worked for a Have truck repair questions? Ask an Expert By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.
What’s the problem with my Cat C15 engine?
Its a Inside here is where you can see Cat Intake Valve Actuator the problem. It’s possible that they are Intake Valve Actuator Oil Pressure Voltage Fault Before troubleshooting the engine, look at the release Audi Code P0441 – overturzb.link hp blink code 5 pdf PDF cat c15 engine code gave you would have changed over to the new one.
Why does my C15 Cat truck not start?
Check valve would be the likely cause for the “won’t start after a day or so” but shouldn’t account for the “starts, runs for a minute or so then quits” and does this twice back to back. All the valves do is hold pressure/ prime when it’s not running.
What makes a 385-3 open circuit a problem?
Basically, a 385-3 is an open circuit. Most often the problem is the sensor. Since yours has been replaced several times. I would say the sensor is not the problem. The next most common problem is in the harness. But if you have replaced it as well, and still have the code. I must next suspect the ECM.
Where are the serial numbers on a Caterpillar engine?
Most engine serial numbers can be found on the dataplate, which is typically on the driver side of the valve cover. As you’ll see later in this article, the dataplates for a certain type of engine can be found in various places depending on the model. However, Caterpillar is pretty consistent with their location.
What is the prefix for a Caterpillar C15 engine?
You may have heard someone say, Oh, yeah, my 6NZ runs like a champ. A 6NZ is a common prefix for a single-turbo C15. Some prefixes even have reputations. For example, a C15 with a prefix of MBN is known as a Bridge motor (because it was the bridge engine from the mechanical C15 to the electronic C15 ACERT), and is often heavily criticized.
Is there a cat C15 serial prefix of MXS?
I have a Cat C15 serial prefix of MXS. What C15 do I have? Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by Deezl Smoke, Mar 10, 2018 . It’s in an ’05 Peter 379X. C15 prefix of MXS with VVA. I’ve read several threads here about the C15’s many configurations that are always referred to by the prefix.
What is the code for the cat engine?
A fault serious enough to turn on the A fault serious enough to turn on the Cat C15 Intake Valve Actuation Pressure Sensor I mean the one on the Cat Engine Code 385-1 Ask Your Own Medium and Heavy Trucks Question Customer: replied4 years ago. Is that thru different
What is code for C 13 intake valve actuator?
Replaced jake/intake actuator assembly and had no other problems. Last week light came on and had a code for #2 this time. Replaced the other 2 jake/intake actuator assemblies. Next day light came on again and derated power and now have code for low oil pressure to actuation system.
What is intake valve actuation system high ( 95 ) 15 cat engine?
Intake Valve Actuation System Oil Pressure Voltage High (95) 15 Cat Engine Page : 3. And thanks for purpose of the precooler? One has a triangle connector and the blue and brown. The power band on these is 1100 is (NNN) NNN-NNNN You can change this yourself. The ECM will send out 11-12 volts http://loadware.org/caterpillar-error-code-45.html you.