Can a fault code be erased on a Hino truck?
On models with a DLC3 diagnostic connector, fault codes can be erased with a tester. Note: when the battery is disconnected, the memory of other electronic devices (watches, etc.) is erased. 3. Carry out road tests of the car. A. Repeat the diagnostic procedure and verify that there are no fault codes.
What does p244b mean on a DPF sensor?
What Does Code P244B Mean? When a code P244B is stored, you may assume that the powertrain control module (PCM) has detected an input signal from the circuit of the diesel particulate filter (DPF) pressure sensor indicating that differential pressure is too high. This code is used exclusively in diesel powered vehicles.
How to find out if your car has a p244b code?
Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P244B code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
When is there no Ne signal on a Hino truck?
There is no “NE” signal to the electronic control unit for 2 seconds or more when the crankshaft is cranked by the starter. 1. Open or short circuit in the sensor circuit of the shaft speed sensor pump.
Why does my car not start when I crank the engine?
If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.
How many times does a Hino lamp flash?
For example, the lamp flashes 1 time, then a pause of 1.5 seconds, then flashes 3 times. This means code 13. 7. If two or more fault codes are stored in the memory of the electronic unit, the codes will be separated by a pause of 2.5 seconds. 8. If there are no faults, the test lamp should flash at an interval of 0.26 seconds.
How does the Hino quick reference guide work?
The Quick Reference Guide is designed to help you quickly look up parts for commonly ordered parts. The format has been changed from previous years. The main sections are in alphabetical order but the Sub-sections are not. The PART NAMEis listed in the first column.
What does p200c mean on OBD-II engine?
If your diesel powered, OBD-II equipped vehicle has stored a code P200C, it means that the powertrain control module (PCM) has detected an excessive degree of diesel particulate filter temperature for engine bank one. Bank 1 is the bank of the engine that contains the number one cylinder.
What are the five groups of Hino parts?
HINO uses five major groups. Engine – Electrical – Drive – Cab Rear Body and Chassis/Tool The sixth column is the FIGURE #that the part can be found in the Hino Electronic Parts Catalog and is helpful if you need other parts in addition to what’s listed in the Quick Reference Guide. See the example shown above from the EPC.
What kind of engine does a Hino truck have?
The outstanding fuel economy, proven reliability and strong residual value make the 268 the ideal truck for pick up and delivery, lease/rental and moving operations. TURBOCHARGED. INTERCOOLED. Award Winning Engines. Hino engines deliver dependable, fuel efficient power.
What kind of warranty does Hino 268 have?
2017 Hino 268A with an 18′ reefer body. EXTENDED WARRANTY IS GOOD UNITL 9-20-2021 OR 250,000 MILES. HINO WIH ALLISON AUTO. NICE 25FT FLATBED READY TO GO TO WORK.
What kind of truck is Hino 268 Reefer?
Off lease, dealer maintained non-CDL 2016 Hino 268A reefer truck. 18′ Morgan insulated body with Thermo King T680. Enter search information and click the Search button below. Use the TAB key to move between fields.