How do I reset my VY Commodore ECU?
The fastest way to reset ECU is to take negative terminal off the battery. Pump the brake pedal till its tight. Turn the head light switch on for 10 seconds then off. The above procedure completly drains power.
How do I reset my Holden Commodore radio?
Turn ignition off. Hold down the UP and DOWN buttons of the trip computer. Turn the ignition on while still holding down both buttons. Release the buttons after 3 seconds (RESET will be flashing).
Is VY Commodore OBD2 compliant?
Freddy’s right, VY isn’t really OBD2 it’s a bit of a mish mash. The engine management is OBD2 but the rest of the car isn’t. So when you think your scan tool is talking to the Engine ECU it’s really talking to the PIM “Powertrain Interface Module” So there’s a fair amount of DTC’s that won’t show up on your scan tool.
Where is the BCM in a VY Commodore?
Its a grey box and with a bunch of connectors, it is located closer to the right hand side of the car then the centre console. It requires a bit of force to take out though. There are four types of BCM units. It just say BCM is behind the cabin fuse panel, lift up off the metal clips and lower the unit.
How do I reset my Holden IQ?
As far as resetting the IQ. There’s no need to open the door, just switch the engine off and restart it and it’ll reset the iq system.
How do I reset my ve radio?
To do this, You have to turn your ignition to the ON position. Turn on your radio and see if it displays CODE or LOC. If it does, turn off the radio. Press and hold down the audio power button together with the SEEK button for about 50-60 minutes.
What year is VY Commodore?
2002
| Holden Commodore (VY) | |
|---|---|
| Production | September 2002 – August 2004 |
| Assembly | Australia: Elizabeth, South Australia |
| Body and chassis | |
| Body style | 4-door sedan 5-door station wagon 4-door utility 2 door coupé utility |
How do I reset my BCM?
Resetting the BCM on a Ford F-150 is as simple as disconnecting or turning off the battery, giving the vehicle a little bit of time and then reconnecting or restarting the battery. Its important to wait at least 15 minutes between draining the vehicle completely and restarting it.
Where is the body control module on a VZ Commodore?
BCM & ECM Authentication (theft deterrent). Location of the PIM: PIM is located in the driver side of the dash, below the instrument panel, near the fuse box.
Is the Holden Commodore VY still in production?
Holden Commodore VY (2001-2004) has been discontinued. See all Holden Wagons. See the Best Wagons in 2021 as rated by Australians on ProductReview.com.au.
Why does my 2002 VX Commodore not start?
2002 vx commodore..wont fire,i have replaced fuel pump and key… I have a vx 2001 series 2 commodore and it won’t start. Like I have a vx 2001 series 2 commodore and it won’t start. Like it will try to and then it dies … read more Vocational, Technical or Tra… Vocational, Technical or Tra… 2002 va beetle 2.0. Not turning over yet cranking.
Where is the OBD2 port on a Holden Commodore?
OBD2 port Holden Commodore VY (2002 – 2004) RHD – Find your plug ! Where is my OBD2 port ? All vehicles are equipped with an OBD port to which you can connect your klavkarr diagnostic case.
What’s the problem with my Holden Commodore 3.6?
WELL the problem is SPARK,,, you have replaced the COILPAACK its in that area some where,,,a mechanic will find the prob for you not to hard for him..but it will sety you back at least $500 i would assume.dean Where is the fuse for the radio? I have a vy 3.6 commodore and the sump is pressurising and blowing oil out dipstick.