How do I get my Jeep Grand Cherokee out of 4 low?
4WD HI To 4WD LOW With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), the ignition switch in the ON position or the engine running, shift the transmission into NEUTRAL, and press the “4WD LOW” button once on the transfer case switch.
How do I get my jeep out of 4 low?
If and when you need maximum traction and you need to move into 4 Lo,
- slow your vehicle down to 2-3 mph. With your Jeep still rolling,
- shift into neutral and slowly.
- firmly pull the lever all the way back.
- Put your Jeep back into gear and you’re good to go.
How do you reset the Uconnect on a 2014 Jeep Grand Cherokee?
Push and hold the Mute button and the other big knob at the same time until the Uconnect reboots (about 5 seconds).
How do I put my Jeep Grand Cherokee in snow mode?
Changing the grand Cherokee to snow mode is really simple. The mode is engaged by pressing this button. All you have to do is pull down on the shift lever and then push the snow mode button. For normal driving, you can also go to Drive Select 2nd gear which allows you to use all of the power on the 4×4 setup.
Is my Jeep Grand Cherokee always 4 wheel drive?
So, YES! The Jeep Grand Cherokee is always in 4WD! This means that the driver’s manual manipulation is out of the equation. To clarify, this change allows the on-board computer to automatically take control of the 4×4 traction system.
When should I use my 4L Jeep?
4 Lo (4L) This position is used when you need maximum traction and maximum power at slower speeds such as rocky surfaces, deep mud or snow, steep or sharp inclines/declines, etc. Your front and rear wheels are engaged in low range using the lower gear ratio, resulting in slower road speed and higher torque.
How do I reset my Uconnect 2014 Jeep?
Five Easy Steps to Reset UConnect®
- Ensure your vehicle is in park and in “Run” mode.
- Press and hold down the volume and tuner knob buttons at the same time.
- Hold down the knobs for 10 – 20 seconds.
- After holding down the knobs, the screen should flash your vehicle brand name and then go dark.
How do I reset my Uconnect 2014?
Uconnect® Hard Reset Procedure
- Press the hot and coup up and down buttons simultaneously for at least five seconds.
- Scroll through the menu that pops up and select the choice prompting you to reset factory defaults.
- Once selecting this option, wait roughly 30 seconds while the system reboots.
Are there any problems with the 2014 Jeep Grand Cherokee?
CarComplaints.com Notes: The 2014 (and 2015) Jeep Grand Cherokee have a serious defect trend of transmission complaints. Most of the complaints are for rough shifting — things like jerking & hesitation when shifting gears. No one has added a helpful site for this 2014 Grand Cherokee problem yet. Be the first!
Why is my Jeep Grand Cherokee not shifting?
The second time driving the Jeep in the morning it would not shift out of 1st gear (8 speed automatic) and the check engine light came on. Drove to the shoulder and turned the Jeep off and restarted – transmission shifted ok but check engine light stayed on.
What happens if your Jeep Grand Cherokee is stuck in Park?
The shift linkage on your Grand Cherokee will usually provide a lifetime of dependable service. But, they can go bad. If you are positive that the gear shifter is not stuck in park (see directly above), then it’s likely that the shift linkage may be bad.
What causes a jeep to get stuck in 4WD?
C1413. They said that message is for a faulty 4WD low switch. I don’t think it was that though because the differential was locked. I’d imagine something mechanical got stuck and I was just lucky it got unstuck. Anybody know what would get stuck mechanically that could have caused my problem?