What does the p1259 code on a Honda mean?

What does the p1259 code on a Honda mean?

If there is a disparity between oil pressure condition in the hydraulic circuit that is determined by the PCM command, and the oil pressure condition that is determined by the status of the VTEC oil pressure switch, the system is considered faulty and the P1259 code is stored. Need more information on how to fix the P1259 HONDA code?

What is the VTEC oil pressure switch error code p1259?

Error Code P1259 is detected when there is a problem in the VTEC oil pressure switch or at the VTEC solenoid valve circuit. Common Symptoms. As with other error codes, Error Code P1259 activates the Check Engine light and registers the code to the vehicle’s memory system.

Where is the p1259 sensor located on a Honda Civic?

It should be noted though while that code P1259 specifically refers to a problem in the VTEC systems’ control/signal/monitoring circuit, some mechanical failure modes can contribute to this code being set and stored. Where is the P1259 sensor located? The image above shows the location of the VTEC oil control solenoid on a Honda Civic engine.

What is the trouble code for Honda VTEC?

P1259 – VTEC system malfunction (Honda) Trouble Code Fault Location Probable Cause P1259 VTEC system malfunction Wiring, VTEC solenoid/pressure switch, E

If there is a disparity between oil pressure condition in the hydraulic circuit that is determined by the PCM command, and the oil pressure condition that is determined by the status of the VTEC oil pressure switch, the system is considered faulty and the P1259 code is stored. Need more information on how to fix the P1259 HONDA code?

It should be noted though while that code P1259 specifically refers to a problem in the VTEC systems’ control/signal/monitoring circuit, some mechanical failure modes can contribute to this code being set and stored. Where is the P1259 sensor located? The image above shows the location of the VTEC oil control solenoid on a Honda Civic engine.

Error Code P1259 is detected when there is a problem in the VTEC oil pressure switch or at the VTEC solenoid valve circuit. Common Symptoms. As with other error codes, Error Code P1259 activates the Check Engine light and registers the code to the vehicle’s memory system.

Where is the VTEC system malfunction code p1259?

Re: VTEC System Malfunction code P1259 has appeared. (… Check your variable valve timing oil pressure switch, it’s located on the passanger side just before the intake manifold, also the solenoid may be dirty or bad. some people say to clean the screen but that requires removing the entire assembly where these two units are… Good luck

What does p1259 stand for in immobilizer code?

There are no codes directly related to P1259. Any problem such as abnormal input or system voltages, intermittent faults, or high resistances in any part of the immobilizer control circuit will set code P1259. Below are some examples of definitions of code P1259 that do not relate to the anti-theft system.

What does a p1259 code mean?

Error Code P1259 is defined as VTEC System Malfunction. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes. Rather, it applies only to specific vehicle makes, such as Honda, Acura, etc. Specification of the definition, troubleshooting, and repairs still vary from one make and model to another.

What does check engine code p1259 mean?

P1259 is a code for vtec malfunction usually cause by a bad vtec solenoid, vtec pressure sensor, low oil level, bad connection.

What is a civic p1259 check engine code?

In the Honda Civic, P1259 means that there is a malfunction in the VTEC system. It is a manufacturer specific code, which means that it means the same thing for all vehicles manufactured by Honda. The VTEC system is an integral part of your Civic’s engine It stands for Variable Valve Timing and Lift Electronic Control System.

What does p1259 failure mean?

Code P1259 is for a VTEC system failure. This is usually caused by low engine oil…….the VTEC system runs off oil pressure and if the oil is low this code will set.