What to do if there is no injector pulse?

If after all this you got the same result, so it’s time to check the injectors itself if there is no injector pulse on one cylinder, by try to unplug injectors one at a time, if the engine starts when a particular injector is unplugged so that it is the defected one that needs to be replaced

What causes no power to fuel injectors?

The most important signals that determine the accuracy of a signal coming out of ECU to injectors are crankshaft position sensor and camshaft position sensor, so to test a bad injector, you have to check the voltage on the injector when the ignition key is turned on: NO VOLTAGE? , so what causes no power to fuel injectors?

How do you test a fuel injector ( ANS )?

Ans: By using a simple diagnostic tool called NOID light, this tool detects a digital signal coming from the ECU and flashes an LED light, so if there is no LED flashing during cranking, this means that there are no pulses coming out of the ECU. Question: How do you test a fuel injector?

How does the engine control unit control the injector pulse?

Question: What controls the fuel injector pulse? Ans: The engine control unit is the electronic brain that used to control the fuel injector pulse by gathering data from various sensors along the fuel line

How to solve ” I have no injector pulse “?

An expert that got 5 achievements. Re: I have no injector pulse. I have plenty of fuel… There is an injector fuse. Pull an injector plug , 1 wire should have 12 volts to it. the other goes to the PCM. The PCM is set up so that it has individual injector drivers, Meaning that you could loose 1 or 2, but loosing all 6 at one time is very unlikely.

Why does my carb spray have no injector pulse?

I have no injector pulse. I have plenty of fuel pressure and both crank sensors and the cam sensor are good. If I spray carb spray through a vacuum hose, it runs fine, but I’m getting nothing through the injectors. What else besides the PCM would control the injectors other than the cam and crank sensors?

Can a PCM loose all 6 injectors at once?

The PCM is set up so that it has individual injector drivers, Meaning that you could loose 1 or 2, but loosing all 6 at one time is very unlikely. Injectors do run off both crank and cam sensors, but mostly off the cam. And when the cam sensor does fail, The PCM goes into default mode, using the last stored run.

How can I test the resistance of my injector?

Another way to test the injector is to measure the resistance of every injector between the two terminals and compare it with the highest and lowest values stated in the injector datasheet; if the result outside the allowable boundaries, then change this injector.

How is the speed of the injector controlled?

The injector in a basic picture is an electronically controlled valve that is supplied with pressurized fuel from the fuel pump at a certain pressure level injector can be electromagnetically opened and closed at very high speed—this speed controlled by the electronic control unit using.

How to fix a leaking fuel injector pump?

The cut off lever on the fuel injector pump was leaking. Not terribly, but enough to notice. So…. I did some research and decided to buy an o-ring kit for the top half of this pump and fix it. I removed the cover, removed the throttle shaft and replaced the 2 o-rings. I did the same with the cut off shaft.

Why do I need to crank my injector pump?

You need to get the air out of the injector lines, otherwise the pump can not build up the pressure against the injector’s valve. The air compresses and act as a spring. Therefore you need to crank the engine and let the air out of the cracked lines.

How does the injector work on a Ford tractor?

Inside the injector is a valve that is shut by a spring. When the pressure is high enough to lift the valve, it opens and you get the high pressure squirt you where expecting. So, from the cracked line you will not get a dangerous squirt.

Why do I get a squirt from my injector pump?

When the pressure is high enough to lift the valve, it opens and you get the high pressure squirt you where expecting. So, from the cracked line you will not get a dangerous squirt. You need to get the air out of the injector lines, otherwise the pump can not build up the pressure against the injector’s valve.

What are the input signals in a pulse injector?

These are the Ne, G, and IGf signals. Inside the ECU, the Ne Signal is used to produce an injection chive signal. The G signal is used to determine the timing of the injection signals. The IGf signal is monitored for fuel delivery fail-safe. (With Conventional EFI, the IG signal is used to produce the injection drive signal.)

How to check injector pulse with multimeter?

Select MSs Pulse on your multi meter. Press the trigger selection button then press negative meter on your multimeter. Initially the unit will read oL, then the readings on your multi meter will stabilize and the actual pulse reading will appear.

Why is the fuel injection computer not working?

In addition on some makes, like Chrysler/Dodge/Jeep, the Fuel Injection Computer will not continue to power the Fuel Pump or the Ignition System with 12 Volts after an initial ten seconds or so. What Tools Do I Need To Test The Crankshaft And Camshaft Positions Sensors?

What does it mean when there is no injector pulse?

In case of that, there is no injector pulse or spark, this means that is your ECU has failed in operating in this case you have to get your ECU changed or visit an expert. You May Like: Low Fuel Light Comes on When Tank Is Full Causes and How to solve it Question: What controls the fuel injector pulse?

What happens if there is no injection signal?

The ECU cannot pulse the injector without an Ne signal and will not start or run if this signal is not present. If the G signal is not present while cranking the engine, the ECU will not be able to identify when to produce the injection signal. The result will be the same, no injection pulse.

Navigation