How do you find the torque specs on a bolt?
Begin with the formula T = K x U x D x P, where T is the torque, K is a standard representing 1.33, U is the coefficient of friction, D is the diameter of the fasteners, and P is the necessary preload.
How do you determine torque requirements?
To calculate load torque, multiply the force (F) by the distance away from the rotational axis, which is the radius of the pulley (r). If the mass of the load (blue box) is 20 Newtons, and the radius of the pulley is 5 cm away, then the required torque for the application is 20 N x 0.05 m = 1 Nm.
What is the torque for a 6mm bolt?
Typical maximum recommended thightening torques for metric bolts
| Size (mm) | Typical Maximum Tightening Torque (Nm) | |
|---|---|---|
| Property Class | ||
| M5 | 7.0 | 11.7 |
| M6 | 11.8 | 19.9 |
| M8 | 28.8 | 48.3 |
What is minimum breaking torque?
Breakaway torque is the rotating force required to “break” the head loose, going in the same direction as applied – tightening. This will usually give a value HIGHER than the original tightening torque because dynamic (when the bolt was tightened) is lower than static (when you try to break loose the bolt head).
How much torque is required to move a car?
Overall transmission (and power-train) efficiency of the modern electric vehicles is within 59 .. 62 %. The answer to your question is 43.2 Nm of Torque required that can be obtained with the transmission ratio value of 15.
How much torque does it take to break a Grade 8 bolt?
My book shows a standard dry torque of 119 ftlbs for 1/2 grade 8.
What is the torque for 7/16 Grade 8 bolt?
Tightening Torque Guide for Grade 5 & 8 Hex Cap Screws
| GRADE 5 | GRADE 8 | |
|---|---|---|
| Coarse Thread | Coarse Thread | |
| 5/16-18 (.3125) | 3338 | 4725 |
| 3/8-16 (.375) | 4950 | 6975 |
| 7/16-14 (.4375) | 6788 | 9600 |
What is the torque tightening value required for M16 bolts?
Typical maximum recommended thightening torques for metric bolts
| Size (mm) | Typical Maximum Tightening Torque (Nm) | |
|---|---|---|
| Property Class | ||
| M10 | 57.3 | 64.1 |
| M12 | 99.8 | 112 |
| M16 | 248 | 277 |
Why loosening torque is less than tightening torque?
In short, it takes less torque to loosen a threaded fastener than it does to tighten it, because the pitched threads act like an inclined plane. And as AvE demonstrates, oil on the threads has the opposite effect, reducing the breakaway torque even further.
What are the torque settings for head bolts?
SOURCE: head bolts torque settings According to my haynes manual for G-S reg, 1989-1998 it goes as follows, Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head. Stage 2:-Tighten all bolts to 40Nm or 30lb ft. Stage 3:-Angle tighten all bolts a further 60 degrees. Stage 4:-Angle tighten all bolts again a further 60 degrees.
What are the torque specifications for a metric bolt?
Metric Bolt Torque. If the bolt diameter is 5 mm, thread series is Coarse, ISO 898-1 Property Class is 8.8, then. Torque for Ecoguard Bolt is 4.0 Nm, Lubricated is 4.6 Nm and dry is 6.2 Nm.
What does torque mean when tightening bolts?
When you tighten a bolt in a bolted joint, you use a twisting force, called torque. Torque is related to bolt tightness , but many additional factors – such as friction – combined into a single “nut factor” can have a significant impact on the relationship of torque to the tightness of the bolted joint.
How do you calculate bolt tension?
Determine the tension force on the bolt. This can also be measured using a force transducer (again, if the value is not already known). Assume the tension force is 3 lbs. Subtract the preload force from the tension force. In our example, the tension force (2 lbs.) subtracted from the preload force (3 lbs.) gives 1 lbs.