What does a distributor ignition module do?

The ignition module is responsible for firing the spark plugs. Each spark plug must fire at exactly the right time for the engine to run properly. The ignition module uses input from the crankshaft position sensor or camshaft position sensor to determine when to fire the spark plugs.

What’s the signs of a bad ignition control module?

Signs of a Bad Ignition Module

Acceleration Issues. The vehicle may shake, vibrate or jerk when the gas pedal is pressed. There may be hesitation or lack of power during increases in speed.
Temperature Problems. A faulty ignition module can cause a vehicle to overheat.
No Power. The engine may turn over without starting.

How do you know when your ignition module is bad?

1. Engine performance issues. One of the first symptoms of a problem with the ignition module are engine performance issues. If the ignition module fails or has any problems it can lead to performance issues with the vehicle, such as misfires, hesitation, loss of power, and even reduced fuel economy.

How does the GM distributor mounted ignition module work?

OK, once the fuel injection computer receives the Distributor Reference Hi Signal, it starts activating the fuel injectors and above 400 RPM, starts to send a 5 Volt Bypass Signal to the ignition control module. It’s with the Bypass Signal that the computer starts to retard and advance ignition timing with the IC Signal.

When does an ignition module need to be replaced?

If the light blinks, the module is good. If the light is blank or constant, the module is bad. Before you attempt to replace the control module, you must rule out other ignition system components. The module is expensive and replacing it is a laborious process. Check the ignition coil for a spark.

What are the symptoms of a bad ignition module?

The following are usually the most common symptoms of a bad spark plug wires, or a bad distributor cap and rotor on this type of GM distributor mounted ignition control module: The car (or truck, or mini-van, or van) starts and runs, but with a misfire. The check engine light is on. Lack of power.

Where does the pick up coil signal go in an ignition module?

This pick up coil signal is sent directly to the ignition control module. The ignition module, upon receiving this pick up coil signal (for all intended purposes it’s a crankshaft position sensor signal) converts it to a digital signal that is now sent to the fuel injection computer.

What does a distributor ignition module do?

the ignition module is responsible for firing the spark plugs. each spark plug must fire at exactly the right time for the engine to run properly. the ignition module uses input from the crankshaft position sensor or camshaft position sensor to determine when to fire the spark plugs.

Is ignition module same as coil?

An ignition coil is the coil in a vehicle’s ignition system used to convert sufficient voltage to spark the spark plugs. The ignition control module helps manage the electrical current used by the ignition coil.

Are all ignition modules the same?

Ignition modules vary in appearance from one application to another, but they all perform the same basic function. These pulses are then delivered to the spark plugs either via a distributor cap, rotor, and spark plug wires, or directly (in the case of distributorless ignition systems.)

Where is the ignition switch module?

distributor
Typically the Ignition Control Module is located inside of the distributor housing or mounted on the side of the engine compartment.

Can you test the GM distributor mounted ignition module?

The GM distributor mounted ignition control module (ICM), can be tested on the car or truck easily. Not only that, you don’t need any expensive tools to do it.

What is an ignition module and what does it do?

In most basic terms, an ignition module is an electronic replacement for old, mechanical contact breakers like ignition points.

What does distributor reference Hi signal mean on ignition module?

This digital signal is called the: Distributor Reference Hi Signal in the majority of the service literature. Also, after receiving the pick up coil signal, the ignition control module starts to switch the primary current (of the ignition coil) On and Off.

What are the symptoms of a bad ignition module?

The following are usually the most common symptoms of a BAD ignition control module on this type of GM distributor mounted ignition control module: The car (or truck, or mini-van, or van) will Crank but NO START. No spark coming from any of the spark plug wires. The Throttle Body Fuel Injectors do not spray gasoline.

Navigation