What happens when you reset the SRS light?

The SRS light will blink twice to indicate that its memory has been erased. Turn off the ignition and wait ten seconds to restart the car. The light should come on for a moment then go out. Figure 2. SRS light (highlighted above) will blink twice when it’s been reset.

When do you need to replace the SRS sensor?

Its very rare for a sensor in the front to go bad but if you have been in to an accident and your airbag didn’t deploy but the seatbelt locked, YOU MUST replace the SRS module.

How do you reset the SRS light on a Honda Civic?

Disconnect the paper clip as soon as the light goes off. When light comes back on reconnect the paperclip. Wait for the light to go off once more then disconnect the paperclip. The SRS light will blink twice to indicate that its memory has been erased. Turn off the ignition and wait ten seconds to restart the car.

What does long Blink on SRS light mean?

Any code with 5, 6, 7, 8, or 10 long blinks means that the problem is with the SRS module. If the code is a 1 or 2 then the problem is with the driver’s or passenger’s air bags respectively. If the code is a 9 then the problem is with the power supply. Figure 3. Service check connector under the glovebox.

How to reset the SRS warning light by yourself?

Step 8: You should hear beeps for 3 seconds, and when the beep is gone, the SRS should turn OFF. Step 9: QUICKLY, Take the paperclip/wires out and the light should come back on. Step 10: When the light comes on, QUICKLY plug the paperclip back in to complete the curcuit again, in a second or so, the SRS light should TURN off

Where can I get a SRS code for my car?

These codes can be read and cleared using an OBD scan tool that you can purchase from your local auto parts retailer. Many auto parts stores will even let you use their OBD scan tool Vehicles free so that you will know what the problem is and possibly purchase parts from their store to fix the problem.

Its very rare for a sensor in the front to go bad but if you have been in to an accident and your airbag didn’t deploy but the seatbelt locked, YOU MUST replace the SRS module.

Where is the fuse for the SRS light?

In most models, this is fuse #40, located in the lower right corner of the fuse block. Turn the ignition switch to “ON” without starting the engine. Leave the ignition on for about one minute to allow the system a chance to reset. Turn the ignition off.

Where is the memory erase signal ( Mes ) plug?

Locate the Memory Erase Signal (MES) plug in the fuse box on the driver side, under the dashboard. It is a yellow plug with two wires in it. Attach the MES plug to the SCS Service Connector. Turn on the ignition, but do not start the vehicle. The SRS light should turn on briefly.

How to read and reset SRS / airbag light?

Battery dying. How to read and reset SRS/ Airbag light? Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Reset SRS/ Airbag light. 1. Locate the fuse panel cover and remove it.

Why does my SRS light keep going on?

Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Step 1 Install a new battery; Step 2 Reset SRS/ Airbag light. Instruction on How to Reset the SRS Light on a Mercedes Benz: 1.

Where to reset the SRS light on a Mercedes?

Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver’s side of the car. Find the port that fits the OBD cable and plug the scan tool’s cable into this port. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts.

Navigation