What to do if your tailgate window is not working?
Check to make sure that the rear wiper is seated correctly. It is worth taking a few minutes to mess around with it for a bit while trying the window. If the wiper blade is not sitting in its holder correctly, there is nothing you can do to make the window move! Try it. It might save you some time and money.
Where is the tail gate control module located?
If operation is not as specified, replace the motor. and 13, check that the power window motor turns. then if they are OK, replace the relay. The tail gate control module is located behind the plastic trim (wall) at the left rear of the vehicle. Beside the small compartment and below the rear speaker
Are there any problems with my Bronco tailgate?
(Playback ID: P2_kRJRi5V-KyXis) An error occurred while retrieving sharing information. Please try again later.
How do you raise the tailgate on a lawn mower?
Turn the motor’s mount bolts in a counterclockwise direction and remove the motor by pulling it free of the window regulator gears. If the glass is in the way (retracted for lowering the tailgate), it can be temporarily raised by working the window regulator arms manually.
How do you remove motor from Bronco tailgate window?
Unplug the motor from the wiring harness by pulling the adapter plug apart or out of the socket on the motor. Turn the motor’s mount bolts in a counterclockwise direction and remove the motor by pulling it free of the window regulator gears.
What kind of regulator does a power window motor use?
Most manufacturers now use cable type regulators. With the cable regulator, the motor drives a wire cable though the mechanism. A series of plastic pulleys guides the cable. A regulator carriage attaches to the cable and to the window glass and slides on the regulator track.
What causes the motor to rotate and lower the power window?
Direct current flow in this position causes the motor to rotate and lower the power window. Back probing the connector will show 12 volts between the two wires and -12 volts if we reverse our test leads. To raise the power window, we push the switch in the opposite direction. This reverses the polarity of current flow within the switch.
What does it mean when your power window is not working?
Looking for symptoms helps guide us to the most likely cause. No sound coming from the door, when we press the power window switch, suggests a bad motor or power is not reaching the motor. Hearing the motor running, without the window working, usually shows the power window regulator or clutch are bad.
How can I tell if my window motor is analog or digital?
With a digital volt meter, we can test to see if power reaches the window motor. If the power window motor has two wires, it is an analog system. We can back probe the connector at the motor, to detect if current flows when we press the switch.
What to do if your power window is not working?
Each car door with a power window has a window regulator to move it. If the regulator goes bad, then pushing the up or down button will not make the window move. You will need to have the window regulator replaced. Every power window requires a window motor to supply the electrical energy.
Is it dangerous to drive with a tailgate open?
Tailgate opens while driving at both city street speeds and highway speeds. Allowing items in bed to fall out on road creating road hazard. This is more than an inconvenience it is dangerous and someone is going to killed. Do something about this. Please.
Why does my power window not move up or down?
1) Bad Window Regulators The mechanism that allows a power window to move up and down is called a window regulator. Each car door with a power window has a window regulator to move it. If the regulator goes bad, then pushing the up or down button will not make the window move.
Why is my driver’s side window not working?
The driver’s side window motor may have gone out, or there should be a short or bad connection in the switch. You could try taking the door card off and inspecting the window switch connector. I’ve had luck in the past just unplugging and plugging it back in when my passenger window was working intermittently.
Why is the side of my car door not working?
The switch on the side of your door may not be functioning properly. Each time you press down on the up or down part of the switch, it wears the switch out just a little bit more. If you press it too aggressively or use it on a regular basis, there may come a point when the switch stops working properly.
Check to make sure that the rear wiper is seated correctly. It is worth taking a few minutes to mess around with it for a bit while trying the window. If the wiper blade is not sitting in its holder correctly, there is nothing you can do to make the window move! Try it. It might save you some time and money.
How to fix a Hilux Surf rear window?
You need to remove the tailgate panel and lubricate the motor and gears, once you have done that try reversing the power cables to the motor, if that works it has to be a broken cable of a fault in the relay box. Silly rabbit, tricks are for kids!!
Where is the control unit on a Hilux Surf?
I would think that it’s one of the wires between the tailgate and main body of the surf, or failing that it’s one of the relays in the control unit which is located behind the nearside trim.
If operation is not as specified, replace the motor. and 13, check that the power window motor turns. then if they are OK, replace the relay. The tail gate control module is located behind the plastic trim (wall) at the left rear of the vehicle. Beside the small compartment and below the rear speaker
What is the back door unlock warning switch?
Back Door Unlock Warning Switch (BE–72) 10. Power Window Motor (BE–73) (a) Connect the positive (+) lead from the battery to terminal 2 and the negative (–) lead to terminal 1 and check that the motor turns clockwise.
How to replace battery on Freelander rear window?
Re: Replaced battery on freelander rear window will not… Disconnect battery reconect after 5 mins on reconnection rear window will go down , use key in rear lock to reset rear window, door lock should now work, if not try rear door relays behind left hand rear panel. You can’t post conmments that contain an email address.
Why is my rear window not working on my 4Runner?
If the bolt is installed and you still suspect a problem, pull off the trim/panel on the driver’s side and look at the interlock switch. Sometimes, if too long a bolt was installed, the switch can become deformed and may no longer work properly. Some folks just wire a jumper across this switch to bypass it.
Where is the transmission relay on a Toyota 4Runner?
On the 1st gen 4Runner, its behind the side panel next to the rear seat on the driver’s side (photo A, below). Pull the tabs and shoulder belt trim to gain access to the panel and relay behind it. In the 2nd gen 4Runner, the relay is in the rear corner of the bed, behind the side panel (see photo B below).