Can you install new seatbelts?
Replacing the entire seat belt assembly on your vehicle is easier then replacing a single part. When you opt to replace the entire seat belt, you do not need to take apart the old pieces to insert a new belt or to fix a broken retractor. Replacing a seat belt can be accomplished in a short amount of time.
What’s the best way to replace a seat belt?
1 Locate the bolts that hold both ends of the current seat belt in place. 2 Unbolt all ends of the old seat belt by using a wrench. 3 Line the new retractor up to the holes that you will be inserting the bolts into. 4 Bolt the new retractor into place, tightening it with your wrench.
Do you need to replace the retractor of a seat belt?
When you opt to replace the entire seat belt, you do not need to take apart the old pieces to insert a new belt or to fix a broken retractor. A seat belt consists of two main parts, the retractor and the buckle.
Where do you unbolt a car seat belt?
Depending on your vehicle, the bolts may be attached to the side of the seat, the floor or the side panel. If you have a three-point seat belt, you will have the shoulder strap, lap belt and the buckle to unbolt. If you have only a lap belt, you will only need to unbolt the belt and buckle. Unbolt all ends of the old seat belt by using a wrench.
How to install a 3 point seat belt?
Replacement Seat Belt 3 point formerly, #welr, FMVSS Federal Safety Approved Retractable Belt: CAUTION: Read these seatbelt instructions for 3 point retractable replacement seat belts thoroughly before installing this replacement safety harness.
Do you have to take a seat belt apart to replace it?
When you opt to replace the entire seat belt, you do not need to take apart the old pieces to insert a new belt or to fix a broken retractor. A seat belt consists of two main parts, the retractor and the buckle. The retractor is the part that that allows the belt to be pulled and retracted. The buckle is the end that you plug the belt into.
How do you install a bench seat belt?
Bench Seat End (20″ floppy end) 2. Bucket Seat End (11″ curved hard sleeve) Insert the hex bolt through the hole in the (E) End of the bench seat belt end as shown in Fig. 3 , and then screw the hex bolt into the existing anchor point (threaded hole) and firmly tighten.
Depending on your vehicle, the bolts may be attached to the side of the seat, the floor or the side panel. If you have a three-point seat belt, you will have the shoulder strap, lap belt and the buckle to unbolt. If you have only a lap belt, you will only need to unbolt the belt and buckle. Unbolt all ends of the old seat belt by using a wrench.
How do you replace a lap belt in a car?
If you have only a lap belt, you will only need to unbolt the belt and buckle. Unbolt all ends of the old seat belt by using a wrench. You will need to unbolt the retractor side as well as the side the seat belt locks into. Line the new retractor up to the holes that you will be inserting the bolts into.
How much does fixing a seatbelt cost?
The replacement cost of a seat belt pretensioner is around $150 to $200. The cost of the parts is about $50 to $100 while the cost of the labor is about $100 to $125. You may be able to reduce the labor if you can find a cheap enough mechanic in your area or simply enlist the help of a buddy that likes to work on cars.
Do car seat belts have a lifetime warranty?
None of the regulations or statutes administered by NHTSA require manufacturers to provide a lifetime warranty for seat belts. However, NHTSA has the authority to require manufacturers to replace seat belts under certain circumstances.
How do you replace a seat belt in a Toyota Camry?
Tighten the bolt with a socket and ratchet. Position the belt retractor in the spot that you removed the old one from and align the mounting holes. Insert the mounting bolt and tighten it with a socket and ratchet. Torque each mounting bolt in the seat belt system to 32 foot-pounds with a torque wrench.
Where can I get a replacement seat belt?
You can replace the bolt with a new replacement one purchased from Wesco and found in our 3 point retractable Replacement Seat Belts Optional Hardware Kit (part # 3pt-rmk) or the hex bolt (7/16″ fine thread Grade 5 or better) from the old seat belt if the car has never been in an accident. (The hex bolt should be firmly tightened.)
Replacement Seat Belt 3 point formerly, #welr, FMVSS Federal Safety Approved Retractable Belt: CAUTION: Read these seatbelt instructions for 3 point retractable replacement seat belts thoroughly before installing this replacement safety harness.
How do you install a seat belt system?
Torque each mounting bolt in the seat belt system to 32 foot-pounds with a torque wrench. Install the rear bottom seat cushion and insert the four mounting bolts. Tighten the bolts with a socket and ratchet then torque to 14 foot-pounds with a torque wrench.