How to install transmission output shaft seal on rear wheel drive truck?

How to Install a Transmission Output Shaft Seal on a Rear Wheel Drive Truck. – YouTube If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations.

What kind of oil does a GMC Sierra use?

ACDelco DEXRON-VI Automatic Transmission Fluid is the most recent release in the well-established DEXRON series of automotive transmission fluids. It… GM Original Equipment Dexos 1 SAE 0W-20 Synthetic Motor Oil by ACDelco®. This product is made of high-quality components to meet and exceed strict quality requirements.

Where is the oil leak on my GMC Sierra?

Suspected the rear main seal, but had a problem with that because it wasn’t wet up inside the large chrome inspection cover on the bellhousing. So up to the dealer we go, and after 3 days they call me and say it’s your oil pan and valley pan under the intake manifold.

What kind of transmission fluid does a Chevy Silverado use?

ACDelco DEXRON-VI Automatic Transmission Fluid is the most recent release in the well-established DEXRON series of automotive transmission fluids. It provides… GM Original Equipment™ Dexron™ VI Automatic Transmission Fluid by ACDelco®.

What does a driveshaft do on a rear wheel drive car?

A driveshaft is the cylindrical shaft that transmits torque from the engine to the wheels. They are most commonly found on rear-wheel drive vehicles, and connect the rear of the transmission to the driveshaft. As the output shaft of the transmission rotates it spins the driveshaft,…

Where does the drive shaft connect to the transmission?

A drive shaft will often have internal splines on the end that connects to the transmission and a universal joint (U-joint) on the end that connects to the differential.

How much does a rear wheel drive drive shaft cost?

If you have a rear wheel or four wheel drive vehicle which has a long drive shaft to power the rear wheels, then expect to pay somewhere in the range of $600 to $2,000. Keep that in mind that the type of vehicle plays a major role in both the price of parts and labor.

How do you remove the driveshaft from a Dodge Ram?

Driveshaft removal (and installation) is straightforward: Using two or three jack stands, support the front and rear ends of the driveshaft. For a two-piece driveshaft, support the center as well. Unbolt the rear U-joint or four-bolt flange on the truck’s differential pinion.

How is the rear differential connected to the driveshaft?

In 4WD trucks, it connects the rear output of the transfer case to the rear differential and a shorter driveshaft going to the front axle. The driveshaft connected to the rear differential is actually referred to as a “propeller” shaft, or “prop” shaft for short.

What kind of bolts do you need to remove a driveshaft?

Remove Driveshaft Bolts Remove the shaft differential flange mounting bolts. These bolts will be very tight so use good quality tools to avoid stripping. Some bolts can head 12 point heads as in this example which used a 13mm 12 point socket to remove.

What happens when a driveshaft is removed from a car?

Something you should know that may not be thought of is when a driveshaft is removed the car will no longer be in park. The car will roll because the link between the drive wheels and transmission is removed. You will need to raise the car or truck up using a floor jack and jackstays. Wear protective eyewear and gloves before you begin. 1.

What to do if your driveshaft is failing?

If you suspect your driveshaft is having an issue, have the vehicle inspected by a professional technician to determine whether the driveshaft should be replaced. The most popular service booked by readers of this article is Vehicle Drivetrain Inspection.

What was the problem with my 2003 Montana?

I have a 2003 montana and having issues with awd groan. Had it to the dealer and they changed the fluid and that had corrected the problem with the groan. But after about 8000km and warmer weather this week its back again.

When do you need to replace a transmission seal?

Slight wear can sometimes be taken up by fitting a shim between the seal and its housing, to change the point of contact. But if a shaft becomes seriously grooved it must be replaced or repaired at a garage or engineering machine shop. This is not a common occurrence, but any point at which a shaft rotates in a seal is a possible leak source.

When do you need a front output shaft bearing replacement?

If you suspect that your vehicle may be having an issue with the front transfer case bearing, have the vehicle inspected by a professional technician, such as one from YourMechanic, to determine if the the car will need a front output shaft bearing replacement.

Do you need to remove drive shaft to replace rear main seal?

It doesn’t matter whether the car is a rear or front wheel, the drive shaft is vital to remove in order to allow more clearance. Now, you might be capable to see the flex plate. You can take the help of a wrench and screwdriver to untie the flex plate. The flex plate is the last layer that covers rear main seal replacement.

What happens if the output shaft bearing is damaged?

Aside from supporting and securing the transfer cases front output shaft, the output shaft bearing also seals gear oil within the transfer case. If the output shaft bearing becomes damaged, it can cause gear oil to leak from the transmission.

What causes oil to leak from front output shaft?

Oil leaking from transfer case. Another symptom of a potential issue with the front output shaft bearing is oil leaking from the transfer case. Aside from supporting and securing the transfer cases front output shaft, the output shaft bearing also seals gear oil within the transfer case.

How to fix a transmission leak in your car?

How to fix a leaking transmission in your car, DIY with Scotty Kilmer. How to find transmission leaks in your car. How to replace an output shaft seal. DIY car repair with Scotty Kilmer, an auto mechanic for the last 45 years. 1. Tie Rod Remover: http://amzn.to/2iSOfyZ 2. Sledge Hammer: http://amzn.to/2klPyH8 3. Forked Tool: http://amzn.to/2jUUv5J

How much does a high gear transmission weigh?

High gear is a direct drive 1 to 1 ratio with a minimal amount of rotating mass. It weighs in at 43 pounds with an aluminum case and extension housing and an even lighter 38 pounds 2 ounces in magnesium.

What kind of transmission does a GM TH350 have?

Turbo 350 Transmission Specs. This transmission replaced the GM Powerglide automatic transmission, which was a 2 speed automatic transmission that was in production for 23 years. The Turbo 350, known by the name TH350, was used in nearly all GM rear wheel drive car and truck applications during its tenure.

How does tooth count on transmission shaft work?

Tooth counts on the input shaft help confirm a certain gear ratio. However, you may not have access to this information if the transmission is still in the car, or a vendor at a swap meet is unwilling to remove the cover. Sometimes replacement inputs have no ID grooves.

Navigation