What does code 16 mean on passenger side air bag?
Code 16 one flash followed by Six flash cycle: Passenger side air bag trouble code. Often means that in a car without a passenger side airbag the resistor that sits in its place has failed but could be any of the following. You’ll need to extract the airbag fault codes to know. DTC B1996: Passenger side air bag short to battery.
What’s the code on the air bag light?
I have a 99 F-150 XL*****with the airbag light on. The code is 25. I replaced the Passenger Air Bag Deactivation switch assembly and have the same code. To replace it I disconnected the battery ground cable, removed the center instrument panel finish panel, disconnected the electrical connection and the screws holding the PAD.
Do you clear trouble codes before resetting airbag light?
Do never clear the trouble codes before you fix the problem caused by the airbag light. Read the codes and get information about what can cause the problem and therefore continue the diagnosis. You should never just reset the airbag light without repairing the problem.
Do you need scanner to read airbag trouble codes?
Working with your airbag system is crucial, and therefore, always read the trouble codes with an OBD2 scanner to get an idea of where to start your troubleshooting. Do never clear the trouble codes before you fix the problem caused by the airbag light.
What does the code on the air bag indicator mean?
If the system detects any problems, it gives you a signal through the airbag indicator by flashing the light several times, giving you the specific problem the test has detected. These flashes are codes, each having its own meaning. The supplemental restraint system (SRS) warning light is most commonly known as the airbag system light.
Is the SRS warning light an air bag code?
These flashes are codes, each having its own meaning. The supplemental restraint system (SRS) warning light is most commonly known as the airbag system light. This is a computer controlled system designed to deploy one or more driver, passenger, and side airbags. How to read air bag codes ?
What is the SDM code for a airbag module?
Right Roof Rail Initiator 1 Deployment Loop Resistance Below Threshold Driver Airbag Module Deployment Circuit – (Single Stage Or Stage 1) Short To Ground or Earth Or Voltage (12 volt VSS) Out Of Range Driver Airbag Module Deployment Circuit – (Single Stage Or Stage 1) Short To Ground or Earth OrVoltage (12 volt VSS) Out Of Range
Where are airbag codes stored in a Chevy?
Below you will find common airbag codes that can be stored in your airbag control module after your vehicle was in an accident. The best part of having your Chevy’s original airbag module reset by MyAirbags is that when you get your airbag control module back and it goes back into the same vehicle that it came out of then it will be plug-n-play.
What does the code 21 mean on a Ford airbag?
Codes 21 to 24 These codes are signaled by two flashes, a two-second pause and the number of flashes that corresponds to the second digit. Code 21 (double flash, pause, one flash) means the diagnostic monitor is not mounted properly.
What does code 13 mean on airbag light?
Code 13 (single flash, pause, three flashes) means that the airbag circuit has shorted to ground and Code 14 (single flash, pause, four flashes) means that the primary crash sensor circuit has shorted to ground.
What is the Flash code for the air bag?
Lamp flash code: 23 1.54 DTC B2295 Error value 26: Passenger side air bag circuit short to ground. Lamp flash code: 23 1.55 DTC B2295 Error value 25: Passenger side air bag circuit open circuit. Lamp flash code: 23 1.56 DTC B2295 Error value 24: Passenger side air bag circuit low resistance on squib.
What does code 21 mean on an airbag?
Code 21 refers to the airbag not being properly mounted. Code 22 informs the driver that the safety sensor output has been shorted, and code 23 states that the safety sensor output is open or grounded.
What does the code 32 on the airbag light mean?
Code 32 (triple flash, pause, two flashes) means the driver side airbag has a circuit open or with high resistance, Code 33 (triple flash, pause, two flashes) means the passenger side airbag has a circuit open or with high resistance, Code 34 (triple flash, pause, four flashes) means the driver side airbag has a shorted circuit or one with low
What does the code 13 on an air bag mean?
Code 13 (single flash, pause, three flashes) means that the airbag circuit has shorted to ground and Code 14 (single flash, pause, four flashes) means that the primary crash sensor circuit has shorted to ground. These codes are signaled by two flashes, a two-second pause and the number of flashes that corresponds to the second digit.
How do you find the airbag diagnostic code?
Airbag Diagnostic Codes. The airbag codes are double digit numbers. To read the codes, count the number of times the light flashes, wait for the pause and count the flashes again. For example, two flashes, a pause and four flashes mean that your airbag system’s problem is a code 24.