How do you remove a CV axle from a Toyota Corolla?
Pry the CV axle from the transaxle, using a large pry bar. There is a ring clip holding it inside the transaxle that needs to be dislodged. Remove the CV axle once the ring clip releases. Some transaxle fluid will leak out.
How do you remove a Toyota axle?
Instructions
- Remove cotter pin by bending legs back together and remove retainer ring.
- Remove 30mm socket using ratchet (breaker bar) or power tool.
- Remove three 17mm fasteners from the bottom (attached to control arm)
- Pull down on control arm and pull the spindle forward to clear the ball joint.
How much does it cost to replace CV joints on Toyota Corolla?
The first table shows costs for a singe axle replacement, which will be for one wheel either at the front or the rear of the vehicle….Double.
| Model | Toyota Corolla |
|---|---|
| Labor | $252 – $321 |
| Parts | $328 – $1150 |
| Total | $580 – $1471 |
How hard is it to replace CV joints?
replacing both sides shouldn’t take any more than 4 hours. have your manual with you, you’d probably need to undo the cv lock nut, separate complete hub assembly from the strut, pull the cv out.
Do CV axles have bearings?
A CV axle bearing incases an inner and outer roller bearing set into one outer race and two inner races with seals at either end. This bearing is used when a car is designed with front or rear wheel drive CV axles. The wheel is bolted to the axle hub which is attached to the end of the CV joint.
How do you replace a CV joint on a Toyota?
This is why a lot of people choose to replace it themselves, and it’s really not very difficult. To fix it yourself, you’ll need a torque wrench and sockets to break the main CV joint lock-nut loose, and be prepared to have to take out the lower ball joint as well.
How does a Toyota front wheel drive CV work?
In front wheel drive Toyotas, the CV joints deliver torque to the front wheels when the vehicle is turning. As mentioned prior, these parts are prone to failure, but it’s rarely an issue of quality.
Why do rear wheel drive vehicles have CV joints?
Rear wheel vehicles and 4WD vehicles also have CV joints. They serve the purpose of transferring torque from the transmission to the wheels on your Toyota at a constant speed. They also handle the up and down motions of travel through the suspension.
What to do if your CV joint is damaged?
If you catch damage to the boot early enough, you can usually get away with simply repacking the grease and replacing the boot — making the repair far cheaper than the alternative. However, if the CV joint has been damaged, you cannot simply repair it, you have to replace the entire part.
Pry the CV axle from the transaxle, using a large pry bar. There is a ring clip holding it inside the transaxle that needs to be dislodged. Remove the CV axle once the ring clip releases. Some transaxle fluid will leak out.
How to replace CV axle and output shaft seal?
With an extra pair of hands, align the axle (including the outer CV bearing cup) positioned straight towards the transmission.
Can a CV axle be replaced on a Toyota Camry?
Here’s a video on the passenger side cv axle replacement performed on a Toyota Camry. This is a longer axle where the axle is “split” in the center by a support bearing. Here’s a video of a axle shaft removal and seal replacement on a Toyota Highlander.
What should I do if my CV shaft is not working?
If that does not work, a few sharp hammer blows on the pry bar should provide enough shock force to compress the ring and get the bearing cup moving. Toyota CV snap rings tend to be stronger than snap rings found in other cars (i.e., Honda, Nissan, etc.—Subaru uses compression pins to hold their inner CV axles, but that’s another story).
How do you remove the hub nut from a corolla?
Place the Corolla on a lift, up to about waist level. Remove the hub cap. Remove the lug nuts with the impact gun and a socket. Remove the wheel. Remove the cotter pin, spindle cap and lock nut on older model Corollas. Remove the hub nut on later model Corollas with the impact gun and a 30 millimeter socket.
Are there any problems with the Toyota Corolla?
This may lead to harsh transmission shifting, the engine stalling, or the engine failing to start. To address this, Toyota issued a safety recall in late 2010 to replace the ECM at no cost to the owner. Overly Sensitive Electric Power Steering System (possible): See 2012-2015 Corolla – Common Problems.
Why does my Toyota Corolla drift to the side?
Specifically, some people say that the steering wheel will “drift” to the side without driver input, essentially causing the car to steer itself. According to reports this happens at speeds over 60 mph. While it’s possible that the electric steering system is overly sensitive, these exact same symptoms would describe a wheel alignment issue.