Where is the starter on a Toyota 4Runner?
Find the starter motor behind the wheel well where you just removed the wheel. Remove the nut holding the cable to the starter motor and pull off the cable. Remove the starter from the side hole in the wheel well. This is a small hole so have patience working it back and forth until it comes out. Figure 2.
Where is the signal wire on a Toyota 4Runner?
The upper red arrow points at the starter motor and the lower red arrow points at the nut holding the positive cable. This is seen from the right wheel well. Next thing to do is to remove the signal wire from the starter motor. The signal wire is the wire that gives the impulse to the starter motor to start cranking the engine.
How do you remove the top of a starter motor?
Use a long extension (about 6″ long) and a swivel together with a 14mm socket when removing the top bolt of the starter motor. Start at the wheel well where you have removed the wheel. Put the socket and the extension behind the cables and feel your way in to the top bolt of the starter motor.
What does it mean when Your starter motor is bad?
If you hear a clicking sound when you turn the ignition on your truck, odds are the starter motor is bad. Sometimes you can hit the starter with a small hammer to get it working again, but this indicates that the starter motor needs replacement. Continue reading to find out how to replace the starter motor on your own.
What kind of torque does a Toyota 4Runner have?
’99 4Runner SR5 5spd 3.4L V6 4WD (U.S), “Tall” Springs, PIAA fogs, KYB Mono Max Front, Gabriel HiJackers Rears, Pioneer Mechless sound, Yakima Loadwarrior with extension, 16″ 2nd Gen Tacoma “Snowflake” TRD Off Road wheels running Michelin X Radials LT2, owned since Oct, 2014.
Most Toyota 4Runners have the starter motor mounted to one side of the engine along the lower area, as most vehicles do. However, the Toyota 4Runner with the 2UZ-FE engine has the starter mounted on top between the two cylinder banks. To change the unit on this model, you will have to remove the intake manifold.
Where is the starter on a Toyota pickup?
The starter motor is one of those components. It sits on the passenger’s side of the engine at the back and attaches to the bell housing.
How can I test my starter without removing it?
The easiest way to check the starter on the vehicle is to use jumper cables to bypass the vehicle’s electrical system. With the ignition turned off and the transmission in “park” — and with all due care — connect one end of the red/positive jumper cable to the positive terminal of the battery.
Why is my Toyota 4Runner not turning over?
If you can’t get your 4Runner to turn over, or it cranks very slowly, it could be a bad starter. If the battery tests good, and all the wiring looks good, the next logical cause is the starter itself. It’s also a possibility that the starter could still be good, but it may just need a good cleaning.
What should I do with my Toyota 4Runner?
Park your Toyota 4Runner in safe place and level surface. Open the hood and disconnect the black, negative battery cable. Raise the vehicle using a floor jack and support it safely on 2 jack stands. Remove the engine splash shield from underside the engine compartment if your particular model is equipped with one.
The solenoid is a black or blue cylinder located on the side wall of the engine, near the battery, usually on the passenger side. You can trace the wire from the solenoid to the starter, which looks like a squat can with a small tube on top. Once the connections are tightened, try to start the car again.
Where is the solenoid on a Toyota 4Runner?
If you hear a clicking noise and nothing else, check the wires connecting to the solenoid and starter to make sure they are solid, unbroken and firmly connected. The solenoid is a black or blue cylinder located on the side wall of the engine, near the battery, usually on the passenger side.
Is there a problem with my Toyota 4 Runner?
Toyota 4 Runners are known for their reliability under all sorts of conditions. This doesn’t mean that you won’t encounter problems with them on occasion, but knowing how to check for what is wrong can help you determine if the problem needs the attention of a professional mechanic, or if it is a small job you can do in your driveway.
Where does the problem begin on a starter motor?
My problem begins at about 90 degrees. Try it, it may work for you and it cost nothing. Check the small wire to the starter motor. It should be a spade connection with the female part of the connection inside an insulated sleeve on the wire.
What to do if your car has no starter?
Normally is starts easily, within one second with the starter motor, no gas needed, and it starts smoothly. When it has the problem, I turn key, and I only hear a click, and the dash lights are lit, but no starter motor sound. Early on I would call for a tow truck, but it usually started when they arrived.
What kind of engine does a Toyota 4Runner have?
This how-to covers all 3rd generation Toyota 4Runners from 1996 to 2002 equipped with the V6 motor and automatic transmission, whether 2WD or 4WD. Four cylinder trucks are slightly different.
Where is the starter located on a 2nd Gen truck?
Figure 3. Starter location through wheel well. (Note: This is a 2nd gen truck.) Remove the two 12mm bolts that secure the brake line to the frame, and move aside the brake line. Remove the plastic intake tube between the intake manifold and the air box, so you have better access to the starter from above.
Where is the solenoid located on a Honda Accord?
The solenoid is a black or blue cylinder located on the side wall of the engine, near the battery, usually on the passenger side. You can trace the wire from the solenoid to the starter, which looks like a squat can with a small tube on top.