What is the torque for Subaru Outback lug nuts?
90 ft-lbs
Subaru Lug Nut Torque Specs Recommendations
| Model | Trim | Torque |
|---|---|---|
| OUTBACK 2.5I | 16″BASE / BASE | 90 ft-lbs |
| OUTBACK 2.5XT | 17″BASE / LIMITED | 90 ft-lbs |
| OUTBACK 3.0R | 17″BASE / LIMITED | 90 ft-lbs |
| OUTBACK 3.6R | 17″BASE / ALL | 90 ft-lbs |
What torque should lug nuts be at?
New wheels should be re-torqued after the first 50 to 100 driving miles.
| Hardware Bolt or Stud Size | Typical Torque Range in Ft/Lbs | Minimum Number of Turns of Hardware Engagement |
|---|---|---|
| 14 x 1.25 mm | 85 – 90 | 9 |
| 7/16 in. | 70 – 80 | 9 |
| 1/2 in. | 75 – 85 | 8 |
| 9/16 in. | 135 – 145 | 8 |
What is the torque for 1/2 inch lug nuts?
to 85-ft-lbs
For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs.
What is the wheel torque spec for a 2019 Subaru Crosstrek?
Reference the model year in the table to see what lug nut torque and size is applicable for your car….Subaru Crosstrek Lug Nut Torque Specs And Sizes (2013 – 2020)
| Subaru Crosstrek | ||
|---|---|---|
| Year | Lug Nut Torque | Lug Nut Size |
| 2017 | 89 lbf·ft (120 N·m) | M12 x 1.25, 19mm socket |
| 2018 | 89 lbf·ft (120 N·m) | M12 x 1.25, 19mm socket |
| 2019 | 89 lbf·ft (120 N·m) | M12 x 1.25, 19mm socket |
What size lug nuts Subaru Outback?
The Subaru Outback lug nut size is M12-1.25, 19mm HexAnd 16mm Length. Making sure Your tires are in the greatest of condition is crucial to not crashing.
What is the lug nut torque on a 2016 Subaru Outback?
The Subaru Outback lug nut torque recommend iS90 ft-lbs. Tightening lug nuts without a torque wrench can be a recipe for disaster. Make sure You tighten them to the manufacturer’s recommended torque and do not overtighten.
How much torque does it take to remove a lug nut?
Car lug nuts are supposed to be torqued to about 100-120 ft lbs, but too often even the pros won’t take out a torque wrench, instead they’ll sow them on with an impact, set a lot higher than 100 ft lbs.
What happens if you over torque lug nuts?
Excessively tightened lug nuts can strip the threads, distort brake rotors, damage the wheel, and possibly shear off the lug stud. Insufficiently tightened lug nuts can come loose, with catastrophic consequences.
How tight should lug nuts be by hand?
Snug them down and tighten pretty much as tight as you can without blowing something out, but not so tight you can loosen it with the samw equipment. Then drive, carefully, check for loose nuts every 25 miles or so, and dont drive fast. until they break off, then back off 1/4 turn.
How many lug nuts does a Subaru have?
20 Lug Nuts
Set of 20 Lug Nuts, 1 Installation Tool & Key Storage Pouch.
How much torque does a Subaru Legacy have?
SUBARU APPLICATION FT-LBS (N-m) AXLE SHAFT NUT FRONT IMPREZA, LEGACY 137 (186)
How much torque does a Subaru Outback lug nut have?
Also make sure you recheck the torque after a few hundred miles. With subies, the standard throughout the years has been closer to the 65-75 ft-lb range (My first gen Haynes manual says 67 ft lbs). I torque mine to 70 and never have issues, but I don’t think you will to any harm over torquing them. Tungsten 2017 2.5 Limited w Eyesight SOLD!
When do the lug nuts come off a Subaru?
The lugs come off six months later with a little bit of force on the Subaru lug wrench. Mind you, I do lubricate the stud threads. I tried torquing up to the 100Nm that my local dealer insists on, and this makes the lugs quite hard to remove after a few months.
How much torque can you put on a lug nut?
It is no surprise then that most lubricant tables recommend a 40-45% reduction of applied torque when using anti-seize on a bolt. So, a lug nut coated with anti-seize should be tightened to a maximum of 49 ft-lbs. Tightening this lug nut to 85 ft-lbs. means it is now over-torqued by 73%!