How to replace the serpentine accessory belt on a Toyota Corolla?
If the old belt seemed loose and the tensioner was very easy to rotate, replace it with the Dorman 419-123 belt tensioner. Place the new belt down on to the left (passenger) side of the engine and wrap the ribbed side around the lowest large pulley near the rear of the engine.
How to replace drive belt or serpentine belt?
How to replace drive belt or serpentine belt Toyota Corolla. VVT-i engine. Years 2000-2009. – YouTube
When to replace serpentine belt on Toyota Yaris?
An adjustment bolt on the alternator provides belt tension on Toyota’s 1.8L engine. This belt is easier to replace than many, but does require that the alternator mounts are loosened up. This engine was used from 2009 to 2013 and is also found on the Yaris, Matrix, Scion xD and Pontiac Vibe.
How do you replace a serpentine car battery?
There should be 1/2″ of deflection at the midpoint of the longest straight run of the belt. 3) Tighten the lower 14mm pivot bolt. 4) Tighten the upper 12mm mounting bolt, below the adjuster. 5) Re-connect the battery. 6) Test. Numerous boisterous screeching clamors or other general motor commotions can be followed back to your serpentine belt.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
How do you remove a serpentine belt from a car?
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
How can I increase the tension on my serpentine belt?
Increase the tension on the belt. If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt.
If you have trouble pulling the old belt off, you may need to rotate the tensioner bolt a few more turns in the counterclockwise direction and then firmly push back the alternator. Slip the old belt off the alternator pulley and then off the other three pulleys before removing it from the engine bay.
Where is the tensioner on a serpentine belt?
Then turn the 19mm belt tensioner hex nut clockwise (towards the driver side of the car) until it stops, compressing the tensioner piston and putting the tensioner in the loose position. With the tensioner still compressed, slip the belt over the water pump and check and make sure it is correctly installed on all other pulleys.
Where are the tensioner bolts on a Toyota Corolla?
One 12mm bolt is situated perpendicular to the car with the head facing towards the passenger side of the vehicle. The second 12mm bolt is the long tensioner adjustment bolt which is parallel with the vehicle and the head facing towards the front bumper. The two 12mm bolts are labeled on Picture # 7 in the row above.
What is the belt number on a Toyota Corolla?
If your 09-13 Corolla was built in Japan, the correct Goodyear Gatorback poly-v belt is part number 4060480.
If the old belt seemed loose and the tensioner was very easy to rotate, replace it with the Dorman 419-123belt tensioner. Place the new belt down on to the left (passenger) side of the engine and wrap the ribbed side around the lowest large pulley near the rear of the engine.
What should tension be on a serpentine belt?
2) Turn the adjustment bolt clockwise until the rearmost length of the thread matches up with mark on the paper made earlier. Check the tension on the belt. There should be 1/2″ of deflection at the midpoint of the longest straight run of the belt.
How much does it cost to replace the drive belt on a Toyota Corolla?
Upfront and transparent pricing. Toyota Corolla Serpentine/Drive Belt Replacement costs $137 on average. What is a serpentine belt and how does it work? A serpentine belt is a relatively long, flat, multi-ribbed belt that is driven by the engine’s crankshaft pulley.
What kind of engine does a Toyota Corolla have?
Owners of other vehicles equipped with the 1.8L 1ZZ-FE engine such as the Toyota Celica, Allion, Premio, Vista, WiLL, Caldina, Matrix, Avensis, Opa, Isis, RAV4, Wish, Chevrolet Prizm, Pontiac Vibe, and Lotus Elise may also find these instructions to be helpful.
What are the components of a serpentine belt?
Some of the components driven by a serpentine belt are an air pump, water pump, power steering, air conditioner, and most importantly the alternator. The Serpentine belt is controlled by either a serpentine belt tensioner or an idle pulley. How does a serpentine belt differ from traditional belt driven engines?