What is the serpentine belt on a VW?
The serpentine belt or v-ribbed belt on a Volkswagen is a flat belt that powers the engine accessories, such as the air conditioning compressor and alternator. Removal of this belt can be accomplished by the vehicle owner, as it requires no special tools.
How do you replace a V-belt on a VW?
Check that the v-belt is properly seated into the engine pulleys. Pull the power steering pump away from the engine and tighten the mounting bolts using a socket. Place a straight edge over the two pulleys at the v-belt’s longest run. Press down at the midpoint of the belt with your finger.
What’s the best way to tighten a V-belt?
Place a straight edge over the two pulleys at the v-belt’s longest run. Press down at the midpoint of the belt with your finger. Measure the distance between the straight edge and the belt with a ruler. The distance should be less that 13/64-inch. Tighten the v-belt by loosening the power steering pump mounting bolts, using a socket.
Where is the timing belt on a Golf Jetta Beetle?
Remove the bumper cover to gain access to the hose clamp at the top of the intercooler. Pull up (vertically) in the top side corners of both the passenger and driver side of grille trim. Then push inward towards engine and once again pull up on the top side corners of both the passenger and driver side of grille trim.
How do you replace a serpentine belt on a VW?
Lay the v-belt into position over the engine pulleys. Check that the v-belt is properly seated into the engine pulleys. Pull the power steering pump away from the engine and tighten the mounting bolts using a socket. Place a straight edge over the two pulleys at the v-belt’s longest run.
How is the tension set on a serpentine belt?
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
Where do I find the serpentine belt routing diagram?
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.
When is the best time to replace a serpentine belt?
This is a good time to look for oil leaks, too. Oil can increase wear on serpentine belts. Most importantly, take the tensioner pulley and any idler pulleys (these are pulleys that do not drive anything, like Power Steering) and give them a spin.
The serpentine belt or v-ribbed belt on a Volkswagen is a flat belt that powers the engine accessories, such as the air conditioning compressor and alternator. Removal of this belt can be accomplished by the vehicle owner, as it requires no special tools.
How often should a serpentine belt be replaced?
And they’re crucial for running everything from alternators to power steering. In other words, when it’s time to replace it, replace it. Serpentine belts will last you a few years, but depending on whom you ask, you’ll need to start thinking about checking it every 50,000 to 60,000 miles.
How do you remove a serpentine belt from an alternator?
Instructions 1. Remove the engine cover 2. Move the cooling line completely out of the way. To do this, release the plastic retention tab and lift the line up and over. 3. To remove the serpentine belt, release tension off of the tensioner. Then grab the serpentine belt between the a/c compressor and alternator just pull it off. 4. Caution!
Check that the v-belt is properly seated into the engine pulleys. Pull the power steering pump away from the engine and tighten the mounting bolts using a socket. Place a straight edge over the two pulleys at the v-belt’s longest run. Press down at the midpoint of the belt with your finger.
What happens if a serpentine belt wears out?
These accessories provide power to important vehicle systems – the electrical system, the power steering system, the cooling system, and even the A/C system. The serpentine belt is responsible for turning all of them. The serpentine belt may not be prone to breaking, but it does wear out over time.
Place a straight edge over the two pulleys at the v-belt’s longest run. Press down at the midpoint of the belt with your finger. Measure the distance between the straight edge and the belt with a ruler. The distance should be less that 13/64-inch. Tighten the v-belt by loosening the power steering pump mounting bolts, using a socket.