What was the first generation of Saturn SC1?
The first generation Saturn SC1 coupes shared the same fixed headlight front fascia as the SL sedans and the SW station wagons, rather than the pop-up headlight design used on the SC2 and the original SC. The SC1 also lacked a rear trunk lid reflector and a rear stabilizer bar.
What kind of engine does a Saturn SC have?
The 1990-1992 Saturn SC had featured a DOHC 1.9L L14 LL0 engine that was rated at 124 hp (92 kW). For the 1993 model year, the original regular SC coupe model was renamed as the SC2 and a new SC1 trim level was introduced.
When did the Saturn’s Series start racing?
Saturn SC’s competed in the SCCA World Challenge in the 1990s, winning several races from 1995 to 1997. Several S-series cars have been used as rally race cars. S-Series cars are also popular in dirt oval racing and autocross.
When did the second generation Saturn SL come out?
The second generation SL sedans and SW station wagons were made from 1996 to 1999. They had both featured a completely redesigned exterior. The interior was mostly the same as on the first generation vehicles, while mechanically they went largely untouched. The redesigned second generation S-series went on sale in 1995 for the 1996 model year.
What kind of engine does a Saturn’s have?
The powerplant used in Saturn S-series automobiles was a straight-4 aluminum piston engine produced by Saturn, a subsidiary of General Motors. The engine was only used in the Saturn S-series line of vehicles (SL, SC, SW) from 1991 through 2002. It was available in chain-driven SOHC or DOHC variants. This was an…
Are there any problems with the Saturn’s series?
Saturn experimented with making these out of plastic, it was a huge failure. ALL of them failed, if you still own one of these cars and it hasn’t been replaced, it has failed. Symptoms include hard starting, rough idle, temperature gauge not working, awful fuel economy, poor performance, and stumbling, among many other things.
When did the Saturn I4 engine come out?
This engine was used from 1995 to 2002. The SOHC engine was available on the base model S-series vehicles (SC1, SL, SL1, SW, SW1) 1992 through 1998 L24 cylinder heads developed issues with cracks developing in the fifth camshaft journal, located closest to #4 cylinder.
What was the compression ratio of the Saturn I4?
The cylinder head was also redesigned to keep the compression ratio at 8.8:1 even with the flat top pistons and now featured provisions for an air injection reaction system. This engine was used from 1995 to 2002. The SOHC engine was available on the base model S-series vehicles (SC1, SL, SL1, SW, SW1)
What kind of Seatbelts did the Saturn’s have?
For the 1995 model year, the seatbelts were changed from the power passive restraint type to the conventional 3-point type. The interior of the vehicle was redesigned with a new dashboard and the addition of a front passenger’s airbag. The center console was updated as well, adding previously absent cup holders.
What kind of door does a Saturn SC have?
A change beginning with the 1999 model year gave the SC a small suicide door (more properly a clamshell door) on the driver’s side to improve rear-seat access. This type of door had previously been used in extended cab pickup trucks, but was an innovation in coupe design.
When did the Saturn SL series come out?
From 1991 to 1992, the Saturn SL-series Sedan trim levels consisted of the SL, the SL1, and the SL2 . The base SL model featured the MP2 manual transmission only, and it had manual steering.
Can you remove the slave cylinder from a Saturn clutch?
Remove the clutch slave cylinder. Do NOT disconnect the hydraulic lines. The Saturn clutch hydraulics are a closed system and are not meant to be serviced. If you accidentally pull one of these lines you will need to buy new hydraulics from Saturn. Do NOT step on the clutch with the slave cylinder removed.
Where is the clutch on a Saturn s?
On the top of the transmission is the upper locator bracket/mount. It connects the transmission to one of the two ‘dogbone’ style motor mounts. Remove the two bolts that secure the bracket to the transmissions and lift it up out of the way.
Do you need a Haynes Manual to replace a Saturn clutch?
These instructions are a conglomeration of several other how-to documents, Saturn FSMs, shop manuals, online postings and other sources of information. These instructions should not be considered a stand alone document and should be used in conjuction with an FSM, Haynes, or Chiltons manual.
Where are the shifter cables on a Saturn s?
Disconnect the shifter cables from the shifter tower and remove them from the transmission bell housing. The cables are attached to the shifter tower by small clips that should just slide off.