How to install an ECU on a Saturn L-series?
1) Insert a master key (black plastic top, not a grey/valet key) into the ignition switch. 2) Turn key to the “ON” position without starting the engine. Security light should turn on and stay on. 3) Wait for 10 minutes or until the security light turns off. 4) Turn key to the “OFF” position for 5 seconds.
How do you cycle the key on a Saturn L-series?
Flagship One’s Engine Computer Specialist Chris is performing an installation of a PCM/ECM Control Module on Saturn L-Series, and then demonstrating a 30-minute GM Key Cycling procedure. 1) Insert a master key (black plastic top, not a grey/valet key) into the ignition switch. 2) Turn key to the “ON” position without starting the engine.
How to reset the engine control module ( ECU )?
The 2 most common ways to reset your car computer is by either unplugging the battery or by resetting the fuse related to the engine control module Will disconnecting battery reset ECU? Disconnect the battery and Switch the ignition key to the on position for about 15 minutes should reset the ECU
What should I do if my ECU light comes back on?
Drive the car for at least 10 miles for the ecu to learn, if there is a problem with your vehicle then the check engine light will come back on and you can analyze the fault code that the ECM throws. These codes will guide you towards the root of the problem and you can begin replacing parts to try to fix the issue.
1) Insert a master key (black plastic top, not a grey/valet key) into the ignition switch. 2) Turn key to the “ON” position without starting the engine. Security light should turn on and stay on. 3) Wait for 10 minutes or until the security light turns off. 4) Turn key to the “OFF” position for 5 seconds.
The 2 most common ways to reset your car computer is by either unplugging the battery or by resetting the fuse related to the engine control module Will disconnecting battery reset ECU? Disconnect the battery and Switch the ignition key to the on position for about 15 minutes should reset the ECU
Flagship One’s Engine Computer Specialist Chris is performing an installation of a PCM/ECM Control Module on Saturn L-Series, and then demonstrating a 30-minute GM Key Cycling procedure. 1) Insert a master key (black plastic top, not a grey/valet key) into the ignition switch. 2) Turn key to the “ON” position without starting the engine.
Drive the car for at least 10 miles for the ecu to learn, if there is a problem with your vehicle then the check engine light will come back on and you can analyze the fault code that the ECM throws. These codes will guide you towards the root of the problem and you can begin replacing parts to try to fix the issue.
Where can I find a Saturn car manual?
SATURN Car Manuals PDF above the page – Sky, Aura, Astra, Outlook, Vue . Saturn Corporation – an American company, founded in 1984, working under the car manufacturing. The administration of the company is located in Troy, which produced cars.
Is the Saturn Corporation part of General Motors?
Saturn Corporation – an American company, founded in 1984, working under the car manufacturing. The administration of the company is located in Troy, which produced cars. This company is part of General Motors . In the state of Tennessee in 1990 was the entry into operation of the new company General Motors. Where he began to develop new cars.
What should I do if my PassLock light is not working?
The most common repair is to replace the ignition lock cylinder or Passlock sensor and perform a relearn procedure. If you find yourself stranded and the engine won’t crank over, turn the ignition off and wait four minutes. Then, try again. If the engine starts, you should be able to make it home.
What’s the relearn procedure for a GM PassLock?
The Passlock family has two basic relearn procedures—a ten-minute procedure and a thirty-minute procedure—and which one you use depends on the system and what components have been replaced. The ten-minute procedure involves trying to start the engine. If nothing happens or the engine starts and dies, the security light will be flashing.
What should I do if my Saturn ignition key is not working?
Check the fuse to make sure that the metal strip inside the fuse is not broken or damaged in any way. If it is, replace the fuse with another fuse of the same amperage. Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start.
What should I do if my PassLock security light goes off?
If nothing happens or the engine starts and dies, the security light will be flashing. Wait ten minutes. The flashing light should go off or illuminate without flashing. When it does, turn the ignition off, wait twenty seconds, and then try to start the engine. If it starts and runs, everything is okay.
How does the ignition switch work on a Saturn?
Saturn vehicles use a transponder inside the ignition key to prevent unauthorized engine starting. There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start.
How to turn on security light without starting engine?
Turn key to the “ON” position without starting the engine. Security light should turn on and stay on. Turn key to the “ON” position without starting the engine. Security light should turn on and stay on. Turn key to the “ON” position without starting the engine. Security light should turn on and stay on. Turn key to the “OFF” position.