Where is the ignition switch on a Saturn?
The problem was due to the original ignition switch which is a $50 part from Saturn. The ignition switch is located on the back end of the ignition lock. The ignition switch sends a code that is generated in the ignition lock to the body control module (BCM). It is a part of the Passlock2 system on the 2004 Saturn.
Why does my selonoid starter light not click?
getting the selonoid to click makes me think your starter is likely the problem. Just my guess. You obviously have power to the solenoid. Hook the clamp end of your test light to an engine ground then touch the test light to the starter post with the switch in start position. If you get no response to your test light the solenoid contacts are bad.
Why does my solenoid say no starter engagement?
You obviously have power to the solenoid. Hook the clamp end of your test light to an engine ground then touch the test light to the starter post with the switch in start position. If you get no response to your test light the solenoid contacts are bad. If you get the test light to light you have problems with the starter.
What to do if your starter wont turn on?
If you don’t have power you will need to gain access to the neutral safety switch (A/T only) and test input and output power. If you have power in, but not out. Confirm the car is in park/neutral before replacing the switch. The power input pin in the ignition switch draws power directly from the battery with no fuse or fusible link seemingly.
Some Saturn models have a connection behind the ignition switch, which will be revealed only when you slide out the entire assembly. Other models have a connection below the ignition switch that can be unclipped prior to sliding out the old ignition switch assembly.
What should I do if my Saturn ignition is not working?
Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.
Can a negative battery be removed from a Saturn?
Remove the negative battery cable from your Saturn’s battery. If you want to be doubly safe, remove the positive battery cable as well. Wait for at least 15 minutes before touching any electrical parts or connections.
Where is the starter fuse on a Saturn?
Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover. Locate the fuse for the starter in the fuse panel using the fuse diagram on the underside of the fuse panel cover.
How does the ignition switch work on a Saturn?
Saturn vehicles use a transponder inside the ignition key to prevent unauthorized engine starting. There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start.
Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.
Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover. Locate the fuse for the starter in the fuse panel using the fuse diagram on the underside of the fuse panel cover.
What happens if you have an ignition switch problem?
Ignition switch problems can also cause issues on the road, such as unexpected shutdowns or electrical problems. To be sure, ignition switch problems are no fun, especially if they’re stopping you from getting to work or school or play. If you’re having an ignition switch problem, taking care of it right away will prevent you from being stranded.
How do you replace an ignition switch on a car?
Slide the new ignition switch assembly into place, making sure you reconnect all of the necessary electrical connections and put the new ignition switch in exactly the same location as the old one was located. Tighten the bolts to securing it in place. Reconnect the negative and positive battery terminals and try your new ignition switch.
How to troubleshoot the ignition system in a Saturn Ion?
It primarily involves checking for sparks on the spark plugs and ignition coils. Remove a park plug wire from the plug and connect it to a spark tester. Ground the tester to the engine, crank the engine and look for a strong spark. Repeat for all the Ion’s wires.
When to replace spark plugs and ignition module?
Replace the coil pack if the same pack has no sparks; replace the ignition module if the same location has none. Proceed with the no-spark test if no sparks appear on all four spark plug wires or both coil packs. Watch the dashboard tachometer for signs of motion while cranking the engine.
What should crankshaft resistance be on Saturn Ion?
Measure the resistance between the crankshaft position sensor’s terminals A and B. (Disengage the DIS module’s five-pin connector first). The resistance should be 700 to 900 ohms. Remove the crankshaft sensor from the engine if the resistance was off.
What to do if your ignition system is not working?
Most causes of ignition system problems can’t be corrected by a non-expert, but there are a few things you can do to discover a problem’s location. It primarily involves checking for sparks on the spark plugs and ignition coils. Remove a park plug wire from the plug and connect it to a spark tester.
What should I do if my Saturn ignition key is not working?
Check the fuse to make sure that the metal strip inside the fuse is not broken or damaged in any way. If it is, replace the fuse with another fuse of the same amperage. Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start.
What should the circuit resistance be on a Saturn Ion?
There’s an open in the circuit resistance is above 200 ohms and a loose terminal or a faulty module if below 200 ohms. Measure the resistance between the crankshaft position sensor’s terminals A and B. (Disengage the DIS module’s five-pin connector first). The resistance should be 700 to 900 ohms.
Some Saturn models have a connection behind the ignition switch, which will be revealed only when you slide out the entire assembly. Other models have a connection below the ignition switch that can be unclipped prior to sliding out the old ignition switch assembly.
Slide the new ignition switch assembly into place, making sure you reconnect all of the necessary electrical connections and put the new ignition switch in exactly the same location as the old one was located. Tighten the bolts to securing it in place. Reconnect the negative and positive battery terminals and try your new ignition switch.
Can a faulty ignition switch cause a car to not start?
There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start. If you are experiencing problems with your ignition key or switch, you may need a simple key reset or you could have a faulty ignition switch that needs to be replaced.
What are the problems with my 2004 ion2?
Need some confirmation. Having intermittent starting problems with my 2004 ION2. Insert key, turn on, lights come on but no turnover. Sit a few minutes, turn on, tries to start but dies as if no gas, or get a turnover and that’s it. Sit another couple of minutes, turn on, lights, no turnover.
What does the PassLock system on a Saturn do?
The Passlock system is intended to prevent a worn (worn keys use to be about to start any of the earlier model Saturns without any security system) or incorrect key from starting the car. If the proper code is not sent then the BCM will shut down the car for up to 10 minutes.
The problem was due to the original ignition switch which is a $50 part from Saturn. The ignition switch is located on the back end of the ignition lock. The ignition switch sends a code that is generated in the ignition lock to the body control module (BCM). It is a part of the Passlock2 system on the 2004 Saturn.
Need some confirmation. Having intermittent starting problems with my 2004 ION2. Insert key, turn on, lights come on but no turnover. Sit a few minutes, turn on, tries to start but dies as if no gas, or get a turnover and that’s it. Sit another couple of minutes, turn on, lights, no turnover.
The Passlock system is intended to prevent a worn (worn keys use to be about to start any of the earlier model Saturns without any security system) or incorrect key from starting the car. If the proper code is not sent then the BCM will shut down the car for up to 10 minutes.
There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start. If you are experiencing problems with your ignition key or switch, you may need a simple key reset or you could have a faulty ignition switch that needs to be replaced.
How do you change the ignition switch on a Saturn?
Remove the negative battery cable from your Saturn’s battery. If you want to be doubly safe, remove the positive battery cable as well. Wait for at least 15 minutes before touching any electrical parts or connections. Unscrew the steering column casings that surround the ignition switch assembly.
Check the fuse to make sure that the metal strip inside the fuse is not broken or damaged in any way. If it is, replace the fuse with another fuse of the same amperage. Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start.
How does the security system work on a Saturn Ion?
The Ion uses two systems that provide different functions, but for the same purpose: to prevent theft. The Ion uses a passive alarm system that arm when you exit the vehicle and lock the doors with the keyless remote. If at any time the doors are opened without the use of the remote or the keys the alarm will sound.
How do you reset passkey on Saturn Ion?
Resetting the PASSKEY can be necessary at times if the programming in the module becomes corrupted or if a new key and key cylinder are installed. To reset the system, get in the car and shut the door. Turn the key on to the “Run” position without cranking the engine. Leave the key there for exactly 10 minutes.
Do you need a new ignition key for a Saturn?
If you think you need a new ignition switch/ lock cylinder, first make sure you don’t simply need a new key. Changing the ignition for Saturn cars is more expensive than buying a replacement key and it will mean that you will have one key for the doors and another for the ignition.
Why is my ignition not working on my Saturn?
If there is a “click” when you try to crank the engine but the engine won’t start, the problem may be with the ignition key transponder. You will need to have both of these components serviced by a Saturn dealership. For specific information about your Saturn’s ignition system, consult the particular vehicle’s manual (see Resources).
Are there any replacement parts for the Saturn Ion?
There are also Saturn Ion OEM parts, Saturn Ion replacements parts, Saturn Ion used parts to fully satisfy your needs. 2003 Saturn Ion Road Test The second new offering actually replaces the S-Series, and that’s the Ion. When Saturn first announced the Ion at the 2002 New York Auto Show they had a lot of fun with the name.
If you think you need a new ignition switch/ lock cylinder, first make sure you don’t simply need a new key. Changing the ignition for Saturn cars is more expensive than buying a replacement key and it will mean that you will have one key for the doors and another for the ignition.
If there is a “click” when you try to crank the engine but the engine won’t start, the problem may be with the ignition key transponder. You will need to have both of these components serviced by a Saturn dealership. For specific information about your Saturn’s ignition system, consult the particular vehicle’s manual (see Resources).
Are there any problems with the 2006 Saturn Ion?
CarComplaints.com Notes: When it comes to the 2006 Ion, the biggest questions are: what big problem is going to pop up next? And how long until GM chooses to address it? Read more » The 2006 Ion has a defective ignition switch that gave owners fits.
Why does my car ignition not start up?
There may be a few reasons why the ignition won’t start the car. Some of them are mechanical (such as a dead battery) and some of them are transponder key related issues. Ignition Cylinder and Car Keys.
There may be a few reasons why the ignition won’t start the car. Some of them are mechanical (such as a dead battery) and some of them are transponder key related issues. Ignition Cylinder and Car Keys.