How to reset service light indicator Saab 9-3 second generation?

Reset by push the CLEAR button & hold down button for at least eight seconds, until ”SERVICE” warning light appears on the display and a chime sounds. When the warning light SERVICE will appear in the display after two bleeps. Switch OFF the ignition. How do you reset service light indicator Saab 9-3 second generation.

What does a red warning light mean on a Saab 9-3?

They are Saab experts and your mechanic is likely not. If the car is overheating, the water temperature gauge would have been in the red, a red warning would appear on the instrument panel and depending on which model 9-3 you have other messages may appear on the driver info center.

How does the brake light work on a Saab?

When a Saab dies, the world becomes a little less quirky. The ! light in triangle, Central Warning Lamp (not the gearbox one) and brake (fluid) light will be turned on when the ABS lamp is lit. The ABS – and TC/ABS modules are powered by the #2 Maxi Fuse, 50 A, in the engine bay main fuse board, to be checked.

What are the warning lights on a Saab?

Saab warning lights, car warning symbols such as engine management light, ABS light, airbag light this guide will help you. We have created this dashboard lights meaning guide and will show you how to deal with an engine light, airbag warning light, ABS light and all of the other car warning signs on your Saab dashboard.

How to reset service light on Saab 9-3?

Switch On the ignition. Depress & release the CLEAR button. Reset by push the CLEAR button & hold down button for at least eight seconds, until ”SERVICE” warning light appears on the display and a chime sounds. When the warning light SERVICE will appear in the display after two bleeps.

What happens if the battery goes out on a Saab 9-3?

If the belt has broken, the engine may overheat (cooling system will not function properly), the battery will not be charged, the A/C compressor will not run and power assistance for steering will be lost. We had problem with steering – It was almost as if the steering wheel was locked. It was extremely hard to turn.

Where is the fault code stored on a Saab?

Since a fault code will be stored in your Saab’s OBD computer, you can use an OBD-II scanner to read those codes. When your Saab check engine light comes on, you may notice:

Select System Settings using the INFO dial. Press in the INFO dial. Select the service info heading using the INFO dial. Press in the INFO dial. Select yes and press INFO dial. Switch the ignition to off and then start the engine to see if service light has been reset. . How can you reset service light indicator Saab 9-3 second generation.

What is the fault code on a Saab?

These units are failing in large numbers, causing the engine light to come on with erratic idle speed and/or rough running, sometimes may produce the following fault codes: P0121, P0122, P0123.

Why does my Saab 9-3 engine cut out?

Saab 9-3 Engine ECU fault causing cutting out when engine hot. Common ECU problem that causes the engine management light to come on and the engine to cut out and not restart when it is hot…

Why are there no warning lights on my Saab?

Bearing in mind I spent Saturday driving a rental 7.5 tonne curtain-side with three warning lights on from Newbury to ExCeL and back with no issues – am I invincible? Or have I used up my share of luck? The right answer is “reason unknown” of course. A lot of the time CEL (and CGL) “coming ons” are just sensor failures.

When to check check engine light on Saab 9-3?

Steady Check Engine Light: If your check engine light is on every time you operate your 9-3, you need to have it checked as soon as possible, especially if you notice performance problems or unusual noises.

Are there any problems with the Saab 9-3?

SAAB 9-3 owners have reported 26 problems related to check engine light on (under the engine and engine cooling category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of SAAB 9-3 based on all problems reported for the 9-3.

What causes MAF sensor to go bad in Saab?

MAF sensor may function fine when the engine is cold then start to malfunction once the engine warms up. A coolant temperature sensor can go bad with time, causing the engine to run rich and preventing it from going into the ‘closed-loop’ mode.

How long does it take to clear service message on Saab 9-3?

Hold down the CLEAR button for 8 seconds (the display will show “Clear” for the first 4 seconds and “Service” for the last 4 seconds)

How do I reset the time for service?

Select “Time for Service” using the INFO button and hold the SET button until it beeps. Select “Yes” using the INFO button (cars with diesel engine: hold the brake pedal depressed) Reset the service indicator by pressing the SET button once. Turn the ignition to OFF position and back on to confirm reset.

How do you reset the service indicator light?

Reset by pressing CLEAR for at least eight seconds, until time for SERVICE appears on the display. Turn the ignition off and then start the vehicle to verify the indicator has been reset. The warning light can only be deleted when it is shown on the Service Indicator Display (SID).

Navigation