Where is the ABS sensor on a Saab?
The first goes from the engine bay to a small connector box on the right hand side (from the back of the car) near the fuel tank. The second half goes from this box, splits about 30-40cm into two seperate looms, one for each wheel.
Why does my car make wheel bearing noise when I turn?
While driving at 30 to 40 MPH on an empty road, turn your steering slight left then right, almost like you’re safely weaving in your lane. Wheel bearing noise (especially in the front) will be amplified when you you make that turn since physics allow more weight of the car to be transferred to one side of the car.
How much does it cost to fix ABS fault on Saab?
As a final step you may need to clear the ABS fault code from the ABS module using op-com/tech 2. However this isn’t compulsory as the system will operate fine. I hope this helps anyone who comes across this problem in their Saab. Total repair cost: £2.79.
How can I tell if my wheel bearing is damaged?
How to Identify Damage or Noise of a Wheel Bearing. Take a jack and use it to lift the vehicle up until the tire is not on the ground. Now try moving the tire in a vertical direction, and then a horizontal one. If the wheel feels free play, then there might be damage to the bearing.
How to test wheel speed sensor on saabscene?
You will need to pull the red connector out to be able to remove the two halfs. Step 3: Now use a multimeter to measure the resistance from each connector for each wire. You can use a small screw driver to open up the shield on the wheel speed sensor to see the wire colours. This brings the number of combination of wires to test down!
What should I do if my ABS sensor goes bad?
1. Bend the wire gently as you go along. A damaged section should kink with little resistance. 2. Failing that, as a last step, you can gently cut a part of the insulation and measure the resistance (using a multimeter) from the connector to the cut part of the insulation.
The first goes from the engine bay to a small connector box on the right hand side (from the back of the car) near the fuel tank. The second half goes from this box, splits about 30-40cm into two seperate looms, one for each wheel.
How to avoid YouTube on a Saab 9-3 2.0T?
If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Maptun Stage 3+ Tune on My 2003 Saab 9-3 2.0T – The Perfect Daily Driver Power! A car channel created by car guys for car guys!
What kind of car is a Saab 9-3?
My current cars include a 2008 Saab 9-3 Turbo X (Maptun Stage 4), 2003 Saab 9-3 (Maptun Stage 3+) and 2006 Saab 9-5 Wagon. Uploads every Wednesday and Saturday! Saab Owners’ Convention 2021 is Coming! Will You be There? Special thanks to Connor for the drone footage!
You will need to pull the red connector out to be able to remove the two halfs. Step 3: Now use a multimeter to measure the resistance from each connector for each wire. You can use a small screw driver to open up the shield on the wheel speed sensor to see the wire colours. This brings the number of combination of wires to test down!
How to reset wheel speed sensor on saabscene?
Step 1: Disconnect the connector from the wheel speed sensor. You will need to pull the blue tab out to be able to push down the button. Unfortantly the blue-tab broke on mine, so I had to use a small flat headed screw driver to shift the blue plastic under the connector to unlock it.
What is ABS error code on saabscene Saab?
My ABS+traction+stability control packed up last week and flagged up a error code. The ABS error code can’t be pulled with a standard OBD scanner, you need either an offical GM Tech2 or alternatively an op-com. So I plugged in my op-com into the car and came back with “Rear Left Wheel Speed Sensor open-circuit or low-voltage”.
Where is the wheel speed sensor on a Saab?
The First Stage to verify that the loom is damaged, rather than the wheel speed sensor itself. The wire loom for the wheel speed sensor has two main sections. The first goes from the engine bay to a small connector box on the right hand side (from the back of the car) near the fuel tank.
As a final step you may need to clear the ABS fault code from the ABS module using op-com/tech 2. However this isn’t compulsory as the system will operate fine. I hope this helps anyone who comes across this problem in their Saab. Total repair cost: £2.79.
Why is my left wheel speed sensor not working?
If you get a reading on two wires, make sure your not connecting two pins together, and if you still are then you’ve got a short in the loom. If so your error code, at a guess, will probably be reading something like “Rear Left Wheel Speed Sensor short-circuit or high-voltage”.
If you get a reading on two wires, make sure your not connecting two pins together, and if you still are then you’ve got a short in the loom. If so your error code, at a guess, will probably be reading something like “Rear Left Wheel Speed Sensor short-circuit or high-voltage”.
Why is my odometer and speedometer not working?
Odometer & speedometer not working ABS & Brake warning lights lit. I have the same problem! what number fuse is it? and where is it located ? 756 people found this helpful.
How do you fix ABS on a Saab?
Push the blue tab back in to lock the connector – or if you broke it like I did, use a small screwdriver to push the blue mechanism across. Step 16: Connect the connector back together near the fuel tank/right wishbone. You will need to push the two halves together while pushing the red part back in.
Why is the ABS light and brake light not working?
I have a 1998 Dodge Ram 1500 Both the ABS light and the brake light are on. Changed the Speed sensor on the differential it didn’t help. I did replace the RWAL/ABS fuse and now the speedo works. Next I’m checking the front wheel sensors after that idk what to try. Any advise would be helpful. I have a 99′ Dodge RAM 2500.
Why is my speedometer and odometer not working?
Then if you try to operate truck, the speedometer would not work (no ODO on mine). Also, if you listen for shifting carefully, the truck was not shifting properly (probably due to no speed input – and this would explain drastically diminished MPG).