What are the torque specs for an intake manifold?
Seal packing: Part No. 08826-00080 or equivalent. Install the gasket to the cylinder head cover. Install the cylinder head cover with the 9 bolts. Uniformly tighten the bolts in several passes. Install the 2 cylinder head covers. Torque: 8 Nm (80 kgf-cm, 69 inch lbs.)
How do you tighten an intake manifold gasket?
The specs are below for all the intake and the valve covers. Tighten the bolts and nuts sequentially in three steps. Always use a new intake manifold gasket. helpful? Thank you for the help.
What’s the torque for a 21 ft lbs bolt?
Sorry, 21 ft lbs are the spec for the torque for those bolts. helpful? Would you happen to have torque sequence? helpful? It did not show me the sequence but center out is the sequence.
When to use a new lower intake manifold?
Tighten the bolts and nuts sequentially in three steps. Always use a new intake manifold gasket. helpful? Thank you for the help. I need the torque specs for what I call the lower intake not sure what the proper name is.
Seal packing: Part No. 08826-00080 or equivalent. Install the gasket to the cylinder head cover. Install the cylinder head cover with the 9 bolts. Uniformly tighten the bolts in several passes. Install the 2 cylinder head covers. Torque: 8 Nm (80 kgf-cm, 69 inch lbs.)
The specs are below for all the intake and the valve covers. Tighten the bolts and nuts sequentially in three steps. Always use a new intake manifold gasket. helpful? Thank you for the help.
How to torque small block Ford intake bolt?
Small Block Ford Intake Bolt Torque Specifications 18 Ft/Lbs – Aluminum Heads 22-25 Ft/Lbs – Iron Heads Do the torque in 2 steps, first just hand tight, second with the torque wrench. IF you do have a spec from the manufacturer follow that. Make sure threads in the head are clean and in good
Sorry, 21 ft lbs are the spec for the torque for those bolts. helpful? Would you happen to have torque sequence? helpful? It did not show me the sequence but center out is the sequence.
How big is the air intake manifold nut?
Valve covers are 71 inch pounds or 8 Nm knock sensor is 29 ft. Lbs or 39 Nm. helpful? intake manifold-11’# 15Nm. Throttle body- 14’# 19Nm. Air intake chamber bolt/nut-32’# 43Nm. Air intake chamber support bolt 14’# 19Nm. helpful? Please login or register to post a reply.
What are the torque specs on a Pontiac?
Pontiac Engine Torque Specs Bolts or Parts Lube or Sealer Torque to: Rocker Studs (screw-in) Engine Oil 55 ft-lbs. Rocker Arm Nuts (Non-Adjustable Rockers) Assembly Lube 20 ft-lbs. Oil Pump Bolts Engine Oil 30 ft-lbs. Oil Pump Cover Bolts Engine Oil 15 ft-lbs.
How big is the Vortec intake manifold bolt?
41 492 55.59 Vortec – Intake Manifold Bolts – VIN Z – LOWER REAR ONLY Type: Bolt 11 132 14.91 Vortec – Intake Manifold – 3 Steps: 2 FtLbs; 9 FtLbs; 11 FtL
What are the torque specifications for a 4.3L V6?
900 101.69 Vortec – Main Bearing Cap Bolts Type: Bolt 81 972 109.82 Vortec – Main Bearing Cap Bolts Type: Bolt 77 924 104.4 Vortec – Main Bearing Cap Bolts Type: Bolt 15 180 20.34 Vortec – Main Bearing Cap Bolts – 2 Steps: 15 FtLbs; +75degs Type: Bolt Crankshaft Position Sensor To Engine Block 8 96 10.85 Type: Bolt
How big is the intake manifold in a Toyota?
Per my FSM and Toyota’s own procedure, the spec is 22 ft. lbs. for the 12mm bolts and nuts in the intake manifold. Having the bolts too loose could lead to the gasket leaking earlier than expected. My service manual says the same thing 22ft lbs.
Where can I find the latest torque specs?
Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.
What should the torque be on a torque table?
Torque specifications are shown either as an exact figure, or a specific range. Follow any special instructions or multi-step directions carefully to assure correct final torque. There may be different specifications for different size bolts, bolts in different positions, tightening bolts in several stages, or a cold engine vs. a warm engine.
How big is the knock sensor on an intake manifold?
Valve covers are 71 inch pounds or 8 Nm knock sensor is 29 ft. Lbs or 39 Nm. helpful? intake manifold-11’# 15Nm.