What should I change in my Porsche Boxster?
This will assure you a crisp, firm-handling ride. There are four main components that need attention when you overhaul your front suspension: control arms, ball joints, sway bar bushings, and tie rods. On the Boxster, the rear suspension is a very similar, yet simpler version of the front: replacement procedures are almost identical.
Is the rear spoiler on a Porsche 997 moving?
The adjustable rear spoiler on your Porsche 997 is an automatically controlled device that changes its height and angle at speed. The spoiler is a moving part and does require servicing, no matter how minute it may be. Here is how to keep it functioning properly. This article applies to the Porsche 997 (2005-2012).
Why does my Porsche Boxster have an AOS problem?
The AOS has caused numerous issues on Porsche engines and is an item to be closely monitored. As the membrane in the AOS fails, oil is sucked into the air intake. Initially this can show up as a check engine light for fuel adaptations with oil being deposited on the o2 sensors causing emission faults.
Can you replace the oil cooler on a Porsche Boxster?
If after replacing the cooler, you need to go to the next stage, having a new oil cooler is not the end of the world and at least eliminates the cooler as the source immediately. If replacing the cooler does not solve the problem, the remaining options are expensive and likely require major engine surgery.
The adjustable rear spoiler on your Porsche 997 is an automatically controlled device that changes its height and angle at speed. The spoiler is a moving part and does require servicing, no matter how minute it may be. Here is how to keep it functioning properly. This article applies to the Porsche 997 (2005-2012).
What should I do about my Porsche Boxster?
This technical article shows you how to perform this relatively easy maintenance task. Here’s some short instructions on this very basic of maintenance tasks. The ultimate project for any Boxster owner – installing a Carrera 996 or 997 engine and instantly increasing horsepower. This Wayne’s definitive guide.
Can a Porsche Boxster 996 engine be replaced?
Replacement is relatively easy and is performed from underneath the car. The oil pan may leak over time – learn how to reseal this and also consider installing a deep sump engine kit at the same time. The Boxster and 996 engines are not necessarily known for being bulletproof.
What kind of differential do you need for a Porsche Boxster?
A Limited Slip Differential is one of those go-fast parts that is an almost requirement for track cars. Quaife differentials are good too, and the differential overhaul is documented here.
What are the parts in a Porsche Boxster?
Included in these kits are the following: NOTE: These kits contain OEM parts that are appropriate for vehicles that have not been modified from their factory states. Each kit contains enough parts to service one vehicle.
What kind of suspension does a Boxster have?
Wishbone / Control Arms: The Boxster uses two separate components to create a virtual A-arm suspension that integrates four joints: two ball joints, one center connection, and one rear rubber bushing. Many suspension problems can be traced back to worn out control arm / wishbone ball joints or bushings.
What causes wobbly steering on a Porsche Boxster?
If the tie rod’s joints are worn, then precise steering is impossible, and the car will also have wobbly front wheels and a possible alignment problem. Sometimes vibrations in the steering wheel can be caused by worn out tie-rods too.
This will assure you a crisp, firm-handling ride. There are four main components that need attention when you overhaul your front suspension: control arms, ball joints, sway bar bushings, and tie rods. On the Boxster, the rear suspension is a very similar, yet simpler version of the front: replacement procedures are almost identical.
What kind of suspension does a Porsche 987 have?
Designed to fit: 2005 – 2012 Porsche Cayman / Boxster (All 987 variants) Product Details Correct the geometry for lowered cars with bump steer ad… Designed to Fit 2005 – 2012 Porsche Boxster / Cayman 2013 – 2016 Porsche Boxster / Cayman Product Details These Eccentric Control Arm Monoball…
Included in these kits are the following: NOTE: These kits contain OEM parts that are appropriate for vehicles that have not been modified from their factory states. Each kit contains enough parts to service one vehicle.
Wishbone / Control Arms: The Boxster uses two separate components to create a virtual A-arm suspension that integrates four joints: two ball joints, one center connection, and one rear rubber bushing. Many suspension problems can be traced back to worn out control arm / wishbone ball joints or bushings.